Liczymy pasujące modele…
The bottle top will need to be printed with supports. I use organic supports; pulling out the very top bit is a little tricky. The model is pretty large so it will need to be printed on a 350 or so printer or be split/glued. With a little…
All the bits you need for a mini travel sized version of the game cathedral, and the source code to print a larger version. Print one each of the lid, playing board and lid_clip pieces for the travel case and board. There is room for a…
Introduction I love this game, and it's getting sort of beaten up from getting carted around. I wanted a version that could be packed as small as possible without sacrificing playability. I went through a lot of marker designs before…
I worked with an inner-city teacher looking for a pencil holder that met a few important requirements: made it easy to scan the classroom to confirm that all pencils were stored was satisfying enough to use that students would return…
FENDER BENDER begins with an opinionated design for building the most effective buffering system with the goal of eliminating as much friction from the system as possible. This was done through careful measurement of resistance all the…
I really liked jessed's pokemon deck box, but made a few changes (I'll let you decide if they're improvements). Things that are changed: There are slots in the lid and base for 1x10x20mm magnets to hold the box sealed Coin holder nubbins…
Why another Filament Buffering Solution? I wanted a solution that met the following requirements: Does a decent job of handling retracting filament (duh) Fully 3d printable while ideally using a minimal amount of filament Retains maximum…
***********IMPORTANT NOTE, THIS IS AN OLDER / UNMAINTAINED DESIGN******** I recommend you get the newer version which has many improvements: https://www.printables.com/model/1097162-swivel-mounted-camera-arm-mount-collection-for-pru the…
This is a simple box with a sliding lid for packing your JBL Go 4. The Go 4 is reasonably rugged, but the woven texture can be difficult to clean if it gets dirt or sand in it; this lets me give it a reasonable amount of protection while…
you probably want the newer update to this: https://www.printables.com/model/497457-arducam-day-night-b0205-case-and-swivel-mount-with which addresses a few issues! Should be pretty straight-forward to print & connect. The back plate will…
I wanted an MMU version of Prolific3D's awesome Pikachu, so here it is! I hope you like it. You can print this as a four color model if you want to use disolvable material -- just chose the "black_Pikachu_V3_MMU.3mf" file. Otherwise, use…
General Info These Panels attach pretty securely to the side of the Repbox without bolts, but if you prefer you can bolt them in place (you won't be drilling holes into the filament storage area, so you won't be impacting your humidity…
Not a lot to say here, once you've got magnets glued in at the right polarity you can print t-shirts on your printer. I've leaned on Jakub's and Severeon's designs & I've included OpenSCAD source so you can tweak or improve. If you've…
I made a custom codenames box that makes management of the existing cards a little bit easier. If I was to do it again, I might make the lid lift off instead of sitting on a hinge; it tends to come down while the box is open. I've…
This has some of the improvements from my Magnetically Sealed Pokemon TCG Deck box, but also is split for multi-material printing. For obvious reasons, I would recommend red, black, and white. ( edit ) I updated the design to be more…
These PTFE stepdown adapters can be used to interconnect thee 6mm tubing to the 4mm tubing going into the printer, accomplishing a frictionless step down as well as allowing easy access when swapping filament for a MMU solution. These are…
Just the word YOPP, for my daughter who played Jojo in Seussical The overhang for the exclamation points may need a little cleanup, but generally this printed better than I expected.
General Info A big ole' box for keeping your filament dry and your spools turning makes life super easy but if you need to load a filament spool into tiny PTFE tube in a high, dark area, it can be a challenge. This is a small little…
This will fit and charge Anker Powerbank models "Anker PowerCore Slim 10000 PD" or "Anker Power Bank, PowerCore Slim 10000". The charging base is designed for a "Anker 40W/8A 5-Port USB Charger PowerPort 5". All of the scad files are…
I wanted a gender pronoun tag to wear to a conference, so I made my own. These are sized to be fitted to a name badge magnet -- I used [this one] ( https://www.amazon.com/gp/product/B001O20V8E/ref=oh_aui_detailpage_o02_s00?ie=UTF8&psc=1 )…
Pretty self-explanatory. While it would theoretically work on any honeycomb wall, it's oriented sideways and at an angle to match the repbox. Labels are included if you're using an MMU and want the sizes to pop a bit
Overview This includes a magnetically mounted ball socket corner mount, and a case for the Arducam Day / Night (B0205) for the Prusa Core One. This is a USB camera for use with octopi, etc. The case should be easily adaptable to fit other…
Should work with any standard 12mm COB led lighting strip. Run four sides for 360 degree lighting. End pieces for either end can be added to secure in a standard tube size. I used a PAUTIX RGB Smart IC COB LED Addressable Strip Light and…
The reinforcement object is merged with the end-cap structure that Greg sells as part of his lamp. Either drag both together onto your slicer then merge them or choose that they are parts of the same object if your slicer is set up for…
To wszystkie aktualnie dostępne wyniki.
