P
Printablesmattloew27
Drink Mix Packet Holder
Printed in PLA with 0.3mm layer height and 5% infill and 2 perimeters. Supports are required under the packet display ledge. Link to Onshape model Comments welcomed.
- Pobrania
- 402
- Polubienia
- 58
- Ocena
- 0
Wszystkie modele
Liczymy pasujące modele…
P
Printablesmattloew27
Costco Cart Folding Tray
I was inspired by the Costco Cart Tray by K_Muller, and I started working on modifications to that design (initially to make it fit on my Prusa MINI) when I discovered that the designer did not allow for remixes. This being the case, I…
- Pobrania
- 309
- Polubienia
- 44
- Ocena
- 0
P
Printablesmattloew27
LEGO Technic Compatible Tread Extension
I love the LEGO Technic Liebherr Crawler Crane LR13000 (42146) , but I felt the Link Tread Wide (88383) was too narrow, so I designed a tread extension. This takes the tread width from 5L to 8L. These parts are printed in ABS with 20%…
- Pobrania
- 101
- Polubienia
- 19
- Ocena
- 0
P
Printablesmattloew27
Instant Noodles Cup Holder with Chop-Stick Holder
Printed in PLA with 0.3mm layer height. Prints best with supports.
- Pobrania
- 32
- Polubienia
- 10
- Ocena
- 0
P
Printablesmattloew27
More Plano 3700 Series Small Parts Organizer Bins
Remix of bins from BadMouthfor the Plano 3700 Series Small Parts Organizer. I extended the range to a 2x and 3x double (double double and triple double, respectively) and a double double with a divider. I also cleaned-up Munchkinator's…
- Pobrania
- 30
- Polubienia
- 9
- Ocena
- 0
P
Printablesmattloew27
Messenger Bag Organizer
Minimal supports are required on the Left, Right, and Center parts as shown below: The unit assembles with 4x M3x6mm socket head screws and hexagonal nuts. The model file is sized for a Timbuk2 messenger bag, but can be modified by…
- Pobrania
- 24
- Polubienia
- 11
- Ocena
- 0
P
Printablesmattloew27
BIC EZ Reach Lighter Sleeve as a LEGO Technic-like Brick
Printed in PLA with 0.2mm layers. No supports were required.
- Pobrania
- 17
- Polubienia
- 5
- Ocena
- 0
P
Printablesmattloew27
Booklet Holder for IKEA Tillgang Tray
A booklet holder designed for the IKEA Tillgang tray. Useful for LEGO building. Support legs are included (optional) for heavy booklets that may otherwise tip the tray. Prints well in PLA and PETG. I used 0.3mm layer height and 10%…
- Pobrania
- 5
- Polubienia
- 0
- Ocena
- 0
P
Printablesmattloew27
Hexagonal Organizer - REMIX
Printed in PLA without supports. Magnet pockets are sized for 12.4mm (~0.5in) square magnets. Link to Onshape model .
- Pobrania
- 4
- Polubienia
- 5
- Ocena
- 0
P
Printablesmattloew27
Hexagonal Spray Can/Bottle Holder
Printed in PETG (PLA is fine too) with 0.25mm layer height, 15% infill, and no supports. Model uploaded works with a Ø60mm (nominal) can/bottle, a snap-mount to a Ø22.5mm tube, and a 3mm wall thickness. The Onshape model uses variables…
- Pobrania
- 4
- Polubienia
- 3
- Ocena
- 0
P
Printablesmattloew27
Booklet Holder for a Lap Desk Tray
A booklet holder designed for a lap desk tray that I got off of Amazon . Useful for LEGO building. Counterweight Brackets are included (optional) for heavy booklets that may otherwise tip the tray. Prints well in PLA and PETG. I used…
- Pobrania
- 4
- Polubienia
- 3
- Ocena
- 0
P
Printablesmattloew27
Booklet Holder for IKEA Stodja Tray
A booklet holder designed for the IKEA Stodja tray. Useful for LEGO building. Support legs are included (optional) for heavy booklets that may otherwise tip the tray. Prints well in PLA and PETG. I used 0.3mm layer height and 10% infill;…
- Pobrania
- 3
- Polubienia
- 2
- Ocena
- 0
P
Printablesmattloew27
Wire-Holder Dividers for Plano 3700 Series Small Parts Organizers
Dividers to hold wires for the Plano 3700 Series Small Parts Organizer. Yes I know what the cut-outs look like.
- Pobrania
- 3
- Polubienia
- 1
- Ocena
- 0
To wszystkie aktualnie dostępne wyniki.