Liczymy pasujące modele…
Mini car spoiler inspired by the Porsche 992 911 spoiler (minus the top arm thing). Can be stuck onto a car or anything with a bit of double-sided tape. I printed mine with PLA and it worked fine. Not print in place, unfortunately. I…
One of the first models I made was a crappy and simple model of a spoiler with dual wings (I'm not sure of the right terminology). I have revised it and made a far better version, including a better mounting system and a slight curve.…
Happymodel Mobula7 1s tinywhoop open prop conversion frame inspired by the flywoo firefly nano baby frame. Weighs about a 4g, 1g lighter than the happymodel ducted frame. Very strong, pretty much will never break as this frame with the…
A thin cover for flight controllers. My frame is very tight and my FC and ESC stack is very tall so I made this cover to stop it from rubbing against the battery strap. both 30x30mm (M3 stack screws) mounting and 20x20mm (M2 stack screws)…
Impulse RC Apex EVO ELRS antenna holder, protects the wire antenna. Just like my other holder for the AOS3.5, bend the holder backwards and insert the ELRS antenna wires, then slowly put everything together. Print with TPU at 100% infill…
Happymodel EP1 2.4g ELRS antenna mount for the AOS 3.5 frame. 4mm height at the standoff mounts, gives enough clearance for the VTX antenna mount. Print with TPU, 25% infill, 5 perimeters. Bend the two halves of the mount, then bend the…
Rough 3D model of the Caddx Ant Lite for designing frames or testing fitment. Designed in blender and dimensionally accurate.
Print in TPU with the side with the camera tab facing down and the wider edge facing up. 25-degree uptilt Caddx ant lite camera mount for the AlphaRC 75mm carbon frame. Should work for other frames with 18mm spaced standoffs.
Replacement for the foam that comes with the GepRC cinelog25. Print in TPU with no supports No specific front or back, just print 4 of them and attach them to the prop guards. Attach with 3M double-sided tape, or the one that comes with…
Cut the original battery holder parts off so that you have two parallel and flush rails which the battery holder clips into. print in TPU
1/15 scale, inspired by the Porsche 992 911 GT3RS rear wing, with the swan neck design. Print in PLA or PETG in the orientation in the stl or 3mf file with tree supports. This gives the best strength on thin parts and also uses the least…
Camera bumper for the AOS 3.5 O3 frame. two versions with the two versions of carbon thicknesses of the frame part, the thick one's supporting bridge thing is thinner than the rest so it can have screw heads go under it if necessary.
My previous ELRS antenna mount was good but it was bulky and heavy so I redesigned a lighter version. Print in TPU without supports This mount only supports round standoffs and not hexagonal standoffs as I had switched out the stock ones…
As the title says, DJI Action camera lens adapter for iPhone 15 Pro/Pro Max should also work with the iPhone 16 Pro lineup. Works only with the main wide camera; the FOV of the ultrawide is too wide. Print in black material or use a black…
Five33 Lightswitch V2 Ultra arm cover with HGLRC LED strip There are 3 versions, a normal cover without LED, one with LED slot for the HGLRC LED, and one with a slit for if you're using an opaque TPU though it will only be visible from…
Filament spool holder for 15x30mm clothing racks/rod things. I have my printer in my closet and there are clothe hanger rods above it, so I made this holder to fit around the rod so that the filament spool rotates more easily and doesn't…
Top mount for various accessories, I made an SSD holder for the Adata SD810. M3 screwholes are spread out 1cm apart from each other in a grid. SSD holder printed in TPU so it grips well, use a 22mm M3 screw and a nut, use countersunk…
Inspired by other similar track planners, but I modelled a filament holder for TPU. This way the track layout is more clear, and you can stack the gates using magnets. Print in PLA, use 2x6mm neodymium magnets, maybe use a vice or pliers…
Blackmagic Pocket Cinema Camera 6k internal mod This is a piece to replace the original flange thing on the first-gen BMPCC 6k. Problem: The original piece is too thick and interferes with some lenses that have a large rear protrusion. I…
To wszystkie aktualnie dostępne wyniki.
