Liczymy pasujące modele…
This is an under-desk mount for the Elgato Stream Deck+. If you detach the base of the Streamdeck, you can use the two screws its attached with to screw it into this mount. Then you'll need two other screws to attach the mount to the…
This fits onto the Ender 3 v3 SE z-axis gantry to collect scraps, the cleaning line & any other offcuts from your printer. If you use a plastic razer you can push the waste straight into the bin. It clears the bed by a few mm height-wise,…
A hex/drill bit holder for Gridfinity that holds 4 rows of 10x 6.5mm hex bits. Each hole has a 0.5mm tolerance so the bits fit securely and can't rotate, but can easily be pulled out. I've left space below each row to print out labels.…
A Gridfinity dual plastic razor/scraper holder. Will hold two of these plastic razers/srapers plus approx 100 additional blades. I needed this to fit into a shallow drawer and this fits perfectly. Fits a 3x1 grid and approx 47mm tall when…
In a pinch I needed a really narrow hex bit extender which would fit a small hole. Designed this to be basically as narrow as possible. When I printed it it cracked when I put the hex bit in, but ultimately held its shape and enabled me…
A Gridfinity holder for the Dymo LabelManager 160 . Takes up a 3x5 grid
A Gridfinity 5x2 holder for an RJ45 crimper and a wire stripper. Wanted to be able to store these in my drawer without taking up much height. My RJ45 crimper default position is open, so to put it in I need to close it, which the…
This hex bit holder holds: 26x short hex bits 9x long hex bits 2x hex extenders In a Gridfinity bin 4 tall x 2 wide x 4U tall
Holds a Draper 6 Piece Diamond Needle File Set - will likely hold most needle file sets in a 4x2 Gridfinity holder. Measure approx 30mm tall when filled, good for shallow drawers. Replaces a much larger and flimsier tool case.
A remix of the Philips Hue Bridge/Hub Skadis holder with thicker walls. Still not entirely happy with the stability and I find the hooks make the Hue Hub sit wonky.
A stackable Gridfinity set to hold an Allen Key set in its case. Enough clearance to stack more items on top. As you can see in the pictures, my allen key holders have a big side and a small side. I've made the tolerance essentially 0mm…
A case for the Raspberry Pi Zero (or Zero 2) W. Has a screw hole at the bottom to use a standard tripod screw. I didn't use any screws to attach the lid to the body, just an elastic band. Original model has the required hardware to use…
A Skadis pegboard mount for the official Raspberry Pi 4 case . I've only left holes for the USB-C and Ethernet ports as these are all I use. If you need access to the other ports you'd need to modify this with more cutouts.
A Gridfinity holder for some medium-sized scissors measuring in at 5x2. Fits these Korbond plastic scissors from Coles: https://www.coles.com.au/product/korbond-plastic-handle-scissors-1-each-5323459
I found a few models on here but none of them fit my needs. Created an enclosure to for the MHCOZY 4 channel WiFi relay/switch. It has a snap fit lid. It has some extra length to fit the bend of the jumper cables I am using.
Created this Kef LSX II remote holder to screw in under my desk. It screws in with 2x 8Gx16mm countersunk timber screws (I used these ones ). Has a notch to enable easy slide in and out. Needs a few supports for the wings that screw into…
This is a Gridfinity drill bit holder which can hold 5 drill bits in a 3x1 (2U height so they can stack) space. The .stl file is set up to hold five bits: 4mm wide x 48.5mm long bit 5mm wide x 60mm long bit 6mm wide x 73.6mm long bit 8mm…
A 5x1 Gridfinity holder for a Small Ratchet (4U Height). Stackable
A Gridfinity 3x2 (2u height) holder for the Craftright 11 Piece precision screwdrivers (found at Bunnings: https://www.bunnings.com.au/craftright-11-piece-precision-screwdriver-set_p6060080) with labels.
A wall-mountable attachment that holds the accessories that come with the Losuy Electric Spin Scrubber . They have a screw hole but can also be stuck to the wall.
Created this Gridfinity 5x1 (3U tall) holder for the Pine64 Pinecil Soldering Iron , plus 2x flux and a tube of wire.
A stackable Gridfinity holder in 4x2 size (3U height). Holds my wire cutters (sorry not sure the brand). It's a bit thin at the bottom of the holding part but works fine.
A tall, stackable Gridfinity holder to hold a Stanley STHT77404 stud finder. 4x2x6 in size, which measures in at 45.2mm tall, or approx 6U Gridfinity.
This adapter uses the included wall mount to attach four different mounts (one for each corner) using M3x12 screws & nuts, which then attach to the Skadis pegboard.
This is a very specific use case, but I had a Dahua camera designed for a Dahua PFA136 adapter that I needed to fit to a Dahua PFA134 junction box as we didn't want to buy and install a new junction box. The Dahua PFA136 has a larger…
A Skadis mount for this DSLRKIT USB-C PoE Splitter: https://www.amazon.com.au/dp/B07TJ3ZNJ4
A stackable Gridfinity holder for the Bosch Ratchet T-Handle Screwdriver . The walls are tall enough that the screwdriver can fit in place and still have items stacked on top of it. Also had some extra space so added 14 hex bit holders.
A simple under-desk/table mount for the LIFX Z TV Strip Power adapter
A 4x2 (4U height) Gridfinity holder for a ratchet and some socket accessories
Quickly mocked up this dust collector to use with a 32mm hole saw on my Ryobi drill. Its basically as tall it can be without affecting use of the hole saw.
Created this Gridfinity 5x1 (3U tall) holder for this battery powered Soldering Iron I have, plus 2x flux and a tube of wire. Originally only had the holder for the Soldering Iron but felt like it was a waste of space so added the space…
An AEG AEGLDM50 Laser Distance Measurer Gridfinity 1x3 holder on its side, measuring at 45.5mm tall for use in shallow drawers
To wszystkie aktualnie dostępne wyniki.
