Liczymy pasujące modele…
These small trays require the use of two pieces of my universal peg plate . You can design your own pegs if you want to use on another type of board and reuse the trays. A few different sizes will be added from time to time so keep an eye…
This universal peg is used in a few tool holders and organizers that I designed for my IKEA Skadis pegboard. They will require supports for the hook. For a good fit in the peg holes, I don't clean the supports completely which leaves a…
This is a simple soldering iron holder for the IKEA Skadis pegboard, using 1 of my universal peg plate . You can always use the holder with a different pegboard system though if you design your own peg plate. It should work with most…
This tray is designed around an Extech MN16A multimeter but it can work with others. Requires 2 of my universal peg plates . Print with supports. The holder could be used with other pegboard systems if you design peg plates for it.
Print flat for optimal strength. The underside fillet might not print perfectly but it can be easily fixed in post. Pictured as used for hardware on a DIY packraft. For permanently sewn or welded-in fixtures that will be hard to replace,…
Replacement inlet deflector for your Shop-Vac vacuum cleaner. Do not print in model orientation. Rotate it 90° so the plate is vertical. The deflection cup will be stronger. Use a good brim and supports under the cup and inside the hose…
I made this as a test piece as I needed to see if I could get the tolerances to work on a boston valve for an inflatable boat. One on end is a 7/8"-14 male thread, on the other there is a barbed fitting. The barbs on mine hold so well I…
The Sterilite 20L gasket containers I have are pretty warped at the lid. The amount of force this puts on the clips makes it very hard to unlatch them. This remix adds small wings so one can open the box much more easily.
Designed for the Filler spool holder . You will need two of my universal peg plate to mount this to your Skadis board. You can design your own pegs if you want to use on another type of board and reuse the rack.
Print flat for optimal strength. The underside fillet might not print perfectly but it can be easily fixed in post. Pictured as used for hardware on a DIY packraft (1" version). For permanently sewn or welded-in fixtures that will be hard…
This design is aimed for water-borne users who require a way to top-up a low-pressure inflatable craft remotely without having to put their mouths directly to the boston valve. More specifically, I made this for my Telkwa DIY packraft so…
Print flat for optimal strength. The underside fillet might not print perfectly but it can be easily fixed in post. Pictured as used for hardware on a DIY packraft (1" version). For permanently sewn or welded-in fixtures that will be hard…
A rounded washer that can add nice color accents over your panels when using countersunk flathead M4 screws and prevent having to countersink the panels. Can also minimize snagging on bolt heads.
A tripod floor star is an indispensable tool if you're going to use a surveying tripod inside on slippery floors. This hub was designed to replace a broken part on an existing product, but it would be very easy to make your own too if you…
Use this part on a Japanese Domestic Market car in order to affix a North-American licence plate. You will need: two M6x20 flathead bolts to affix the adapter to the car two M5 hex nuts two washers two M5 button head bolts to affix the…
I made this to use on the bolt from Lucian Brandus' ruler stop , matching the thickness of that tool. It's a tight fit but it's by design.
Disclaimer: DO NOT USE THIS FOR LEGAL SURVEYING Inspired by the Leica GZS4-1, it doesn't require a dedicated tribrach or adapter. Will work with most surveying tripods, but is designed to fit snugly on a Leica-style tribrach and a Leica…
I wanted to be able to use the vise on a soldering helping hand steel plate. This base accomodates two small 3/8" rare earth magnets. If the sockets aren't exactly deep enough, you can shim with a tape of some sort around the magnets. I…
I wanted to make the box jellyfish enclosure for a while but, having terrible trouble sourcing affordable polycarbonate sheets in the last year, I fell back to opaque panels which I could only find in imperial thicknesses. I settled with…
Designed to mount an IKEA Nordmärke USB hub cleanly onto the edge of an IKEA Skadis panel. The cable is routed to the back by an opening in the puck. Requires two of my Skadis universal peg . The rubber gasket from the Nordmärke needs to…
This small stud is the perfect size for #8 wood screws. The cable seat is made for a 10mm cable but it should work with other close dimensions. The ziptie opening fits small ones, around 2.5x1.2mm cross-section. Single pivot point…
A small cap to protect GNSS survey equipment mounting threads from dirt and debris. Made for the Emlid RX but works well with Emlid RS2 or other tools with a base 40mm or more diameter that have 5/8-11 threading. Printing: Best…
This mount is the perfect way to hang your hydration bladder to dry. I was tired of hanging mine on open cupboard doors so I realized I could use my Skadis pegboards. The base plate uses my universal peg format and a modified peg with a…
I designed this around an old external HD adapter that has dual output (12V/5V) on a DIN-422 4-pin connector. I only needed 12V so only one circuit can be wired in - there isn't enough room for 4 leads in there, it's very tight. The…
I used this channel in a concrete slab mold for my MK3S+ to relocate the screen outside of my custom LACK table enclosure. It should work with almost any LACK-based enclosure with a slab up to 50mm thick. The ribbon cable connectors pass…
This very simple wall holder is designed around a Stanley speed square. It might work with other brands and models. The overall width is 50mm. There is a slight lip to retain the square. Counterbored screw holes fit UTS #6 screws.
After searching for simple wall holders for an Olfa knife, I wasn't satisfied with anything. They all either held the knife from one end or were dependent on how far the fastening knob was on the knife. This hook cradles the knob with a…
This model is made off a scan of the original sticker emblem. I added a 12° chamfer to the edges for a clean look. For better adhesion on the tailgate, print on a smooth plate. I printed it with PETG and using the usual window cleaner…
To wszystkie aktualnie dostępne wyniki.
