P
PrintablesAndrewY
Fish Trap / quarantine
Remix of https://www.thingiverse.com/thing:3364837 adapted to clip on the top support of a bowfront aquarium Category: Other
- Pobrania
- 114
- Polubienia
- 12
- Ocena
- 0
Wszystkie modele
Liczymy pasujące modele…
P
PrintablesAndrewY
Marineland Canister Filter Loc-Line 1/2in adaptor
Adapted from https://www.thingiverse.com/thing:4873052 to fit a Marineland canister filter to connect the canister filter outlet to the Loc-line items. 2 versions. One with and without a snap lock ring inside the part. Ended up using the…
- Pobrania
- 46
- Polubienia
- 2
- Ocena
- 0
P
PrintablesAndrewY
Natural Gas/Propane Adaptor for Coleman Powermate Pulse Plus 1750
Natural Gas or Propane carb adaptor. Fits between the air cleaner and the carb. Set up to use a 7/16 hose to connect to pressure regulator. Gasoline operation is not affected. Will need longer screws to attach airbox and adaptor as the…
- Pobrania
- 44
- Polubienia
- 3
- Ocena
- 0
P
PrintablesAndrewY
T8 Aquarium dual LED bulb and end caps
Convert a fluorescent aquarium hood light to hold 2 LED bulb replacements. Some wiring required. I used the "power at one end" lamps and soldered the wires to the posts. Ran the wires through the end cap and installed the caps to cover…
- Pobrania
- 42
- Polubienia
- 9
- Ocena
- 0
P
PrintablesAndrewY
Christmas Ornaments
Christmas ornaments I designed to sneak onto the Christmas tree at work.
- Pobrania
- 34
- Polubienia
- 7
- Ocena
- 0
P
PrintablesAndrewY
Makergear tool holder
Added a Palette to the side of my Makergear M2 and had to remove my tool holder. Designed this so I could mount my tools below the Palette 2. Used an existing unused hole in the side of my Makergear M2.
- Pobrania
- 14
- Polubienia
- 1
- Ocena
- 0
P
PrintablesAndrewY
Sophie Hueforge
Project: Sophie B&W Print at 100% infill with a layer height of 0.08mm with a base layer of 0.16mm The Model is 200x294.57mm in size You may print at higher layer heights below the Min Depth of 0.72mm The Max Depth is 2.2mm and the Actual…
- Pobrania
- 13
- Polubienia
- 0
- Ocena
- 0
P
PrintablesAndrewY
Oregon Coast Sunset
These are the settings HueForge generated. I used PLA for everything. Had some off brand filament that was not in the list of choices. Using close enough colors should get about the same result. Print at 100% infill with a layer height of…
- Pobrania
- 12
- Polubienia
- 4
- Ocena
- 0
P
PrintablesAndrewY
Waylon The Dog
Project: Waylon.hfp Print at 100% infill with a layer height of 0.08mm with a base layer of 0.16mm The Model is 200x299.96mm in size You may print at higher layer heights below the Min Depth of 0.48mm The Max Depth is 2.2mm and the Actual…
- Pobrania
- 11
- Polubienia
- 1
- Ocena
- 0
P
PrintablesAndrewY
My Dog Sophie
Project: Sophie.hfp Print at 100% infill with a layer height of 0.08mm with a base layer of 0.16mm The Model is 200x266.67mm in size You may print at higher layer heights below the Min Depth of 0.48mm The Max Depth is 2.1mm and the Actual…
- Pobrania
- 11
- Polubienia
- 3
- Ocena
- 0
P
PrintablesAndrewY
Thermometer
Project .ino and and web interface preview attached
- Pobrania
- 10
- Polubienia
- 2
- Ocena
- 0
P
PrintablesAndrewY
Bracket for blinking LEDs and firmware for easier setup of clock
Based on the work from https://www.thingiverse.com/thing:5437453 Added a bracket for 2x 5mm LED bulbs in-between the minute and hour. Bulbs wire to the ESP chip. Here are the features I've added to the ESP firmware. -Using an ESP-12F…
- Pobrania
- 4
- Polubienia
- 0
- Ocena
- 0
P
PrintablesAndrewY
MakerGear M2 Z axis Knob
Made to fit on the Makergear M2 Z axis threaded rod. This will fit the locking ring the original z adjustment knob uses. Needed a smaller knob with the extruder I installed. The original knob would contact the new extruder setup I…
- Pobrania
- 3
- Polubienia
- 0
- Ocena
- 0
To wszystkie aktualnie dostępne wyniki.