Liczymy pasujące modele…
You can tape this thing with 20mm double sided tape to e.g. the door of your kitchen sink to have a proper way to store multiple roles of trash bags. Category: Household Supplies
Fits the 12x22mm labels from e.g. the NIIMBOT D110
Use this tool to measure the right distance from the front to mount your doors into an IKEA KALLAX.
I had a spare PureBase 500 laying around that I wanted to use for my NAS/Homeserver becasue it has sound dampening and quite large fans that I can run pretty slow but originally this case can only hold 2x 3,5" drives. This adapter has…
Most of these cheap microphone arms have a really bad mounting clamp, therefore I designed a new one. I used two screw to mount mine, because I have a solid wood table. But if you don't want or can't screw into your table, I designed a…
Small storage containers that can be closed with the lid of an old pringles can (Only tested with cans from Germany. Not sure if they are the same in every part of the world). The container are either 25mm or 50mm high, and have one, two,…
With this holder you can use two 8x2mm disc magnets to attach a pen with an diameter of 15mm (designed for Edding 3000) to a magnetic surface e.g. an fridge. The holes are intentionaly a bit bigger than the magnet (8,4x2,2) because I…
I liked the case because I didn't had a plate for my Lily, but the legs were too much work for me and I also didn't had the screws :D So I removed the legs and pulled down the edge to act as a stand (including 4 degree tilt) Print…
We organised a workshop in our local hackerspace to build CO2 sensors with a bunch of people so you can take care of your air quality at home. The sensors runs ESPHome so you can integrate is easily into your smart home like e.g.…
The original feet on the U1 are "not the best" and I had an additional pair of anti-vibration feet from my P1 laying around, so I came up with this small adapter to use them on my U1.
That's the model I gave away to some people at NixCON23. Just add a colorchange at the last one or two layers depending on your layerheight to get a multi color print.
They switched to some new "child safe" caps a while back, and they break super easily now. After one spilled bottle in my workshop, I decided to design and print a new one :D Prints fine without support. Use a low resolution like 0.2mm to…
Because the smaller UMC devices from Behringer don't have the four screws at the sides, all of the already available stand wont work for them. Therefore I designed this simple wedge to make it a bit more easy to use because you can reach…
This will use 4 8mmx2mm round magnets to stick to the whiteboard. If it's sliding down due to it's own weight attach something sticky to the backside of it. For a example some of these small soft furniture foot covers. Category: Tool…
Printing Print standing up as it is, with tree suports and quite a few walls. Probably also a good idea to use PETG. Hardware You will need two short M4 screws and two nuts to mount the holder to the backplate.
Even when the lamp is off, it draws a little amount of power due to the wireless receiver. With this plug the cable don't wiggle around because you can connect both ends but they are not electrically connected so you don't waste any…
Print this in TPU and set the slicer to 0 top and 0 bottom layers. With 10% grid infill and 2 perimeters you get a nice squishy part which will absorb the shock. Can easily be mounted with two small pieces of doublesided tape.
This adapter let's you use your Kärcher equipment (35mm diameter) on your Orfeld vacuum. Print Instructions Print standing up (like it is imported) and activate supports.
The black valve cap is sometimes pretty tight from the factory. So I made this kind of "wrench" to open them more easily.
This is for the following product from Action: https://www.action.com/de-de/p/3217439/led-pixeltafel/ I didn't liked the look of the display so I designed a thin diffuser an a thicker frame to make it look like a picture frame. The…
The VARIERA is perfect as a little bin for you shampoo and shower gel, but it lacks some drainage and the underside of the bottles get grimy. Pro tip: Also drill some holes in the bottom of the VARIERA, to get rid the water.
The bottle is prone to tip, so I designed this stand that will increase the stability a lot. Due to the small gap, your printer does not need to be perfectly calibrated and it will still fit the bottle. Category: Sport & Outdoors
We use this tombstone at work for the most recent software that we got rid of, so I wanted to be able to swap the labeling easily without printing a new tombstone every time. It uses two 10x2mm round magnets which should hold without glue…
This can be used with the Apeman C660 Dashcam as a replacement for the lever of the sucker cup mount. The hole in the middle is pretty tight so it wont fall off Category: Automotive
After converting my pump to the Schwalbe Click system, there was no longer a way to attach the hose to the pump, so I desinged this. Don't print in PLA, but rather somthing like PETG to retain the clamping force. You will need a M4 bolt…
PETG is sufficient for the heat during brewing and worked here for a few weeks before I got a new decanter. There are already other adapters on Printables for this problem, but I found them too complex and wanted a simpler and more sturdy…
So you can easily carry an additional stick of glue :)
To wszystkie aktualnie dostępne wyniki.
