Liczymy pasujące modele…
The feet on my V3 PLUS were not quite flat, I designed this, it fits over the periphery of the original feet, with a flare on the bottom to deform it to release gravity, and now my machine runs very stable! Print settings: material…
A version of the tail light mix specifically for my L508. I printed it in ABS, it needs support and it works great!
为42-40 步进电机固定在ENDER 3 Z轴位置驱动定制，左右两侧均可固定。固定螺丝为M5+T型螺母。 It for 42-40 Stepper motor work in Ender 3 printer Z AXIS，can use double.The fixing screws are M5 + T nuts. Category: 3D Printer Parts
为3DPrintMill原厂挤出机定制，可以让你的挤出更顺畅，同时使用TPU成功率提高。 Customized for the original 3DPrintMill extruder, it allows you to have a smoother extrusion while using TPU with an increased success rate.…
A simply case with Monroe. Category: Mobile Phone
Q5 original glass is not a smooth surface, especially easy to accumulate to some residue, cleaning is not very convenient. So I designed and made this glass fixing clip. It can be used for round hot bed glass with diameter 220mm and…
这是一个用matter and form 扫描仪 MFS1V1R 扫描的存钱罐。四肢因为阴影的关系有一些缺陷，晚些时候我会完善它。 Category: Scans & Replicas
The stock motherboard fan was too noisy, I tested it with my phone at over 65db, so I made this and after I measured it with my phone app, it reduced it by about 5db 原装的主板风扇实在太吵，我用手机测试超过65db，所以我做了这个，经过我用手机app的测量，降低了约5db Print Settings…
扫描工具 scanner：sony XZ1 处理软件 soft：3D 大师 Category: Scans & Replicas
迈克尔之前做的2020适配架，虽然是无螺丝方案，但是很大，而且只能装在特定的位置（ENDER 3），因此我在他的基础上修改了一个用M5+T型螺母来固定的版本。 Michael's previous 2020 adapter, although a screwless solution, is large and can only be installed in a specific position, so I modified a version fixed with…
我一直在找能固定好热床玻璃，又不用占用打印面积的玻璃夹子，但遗憾的是没有发现很合适的，所以我做了这个。目前使用效果还可以。但需要更多人来测试和修改，STP文件已放出，希望大家能帮助一起完善，谢谢！ I have been looking for a glass clip that can fix the hot bed glass without taking up the printed area, but unfortunately I didn't find it…
CR2020原配的部件在换料的时候很不方便，经常出现耗材无法金属挤出座的孔洞这种情况。另外我的机器批次比较老，没有顶盖固定线缆，所以顺便做了一个线缆盖，直接卡在挤出座PCB安装顶盖上。还有前面板的字体，我不太喜欢，所以更改为现在的样子。 The original parts of the CR2020 are inconvenient when refueling, and there are often cases where the consumables…
专为CR2020设计，风扇为rlf35-8/14n，出风口风向对准打印制品和喷嘴下方，加热块需要跳转180度摆放，以获得最佳位置。（其实是因为市售的硅胶套都只能这么装） PS：我暂时是使用PLA印刷，稍后我会试试ABS Designed for the CR2020, the fan is rlf35-8/14n, the air outlet is aligned with the printed product and under the nozzle, and…
专为创想三维CR2020设计的后置或前置料架，侧面也可以使用，但需要垫一些纸片已填充缝隙，因为侧面的钣金距离和前后数据不一致。 目前工作良好。欢迎大家使用。 PS：尺寸有一些误差，详情可见侧视图。那会导致架子并不会完全平整的安装，不过实际使用中我认为并不影响，所以暂时没有修订，后续我可能会修改它。 The rear or front spool holder designed for the CR2020 can also be used on the side, but…
very simply cover，Plug and Play！ Category: 3D Printers
使用Wahao Duplicator 6 "Verloo Duct" Remix (40x40x20mm blower fan)修改，使用ABS印刷。安装面根据cr2020情况往上加了1.5mm。目前运转良好。非常感谢uncleskippy！ Modified with the Wahao Duplicator 6 "Verloo Duct" Remix (40x40x20mm blower fan), print by ABS,the mounting surface…
To wszystkie aktualnie dostępne wyniki.
