P
PrintablesEdGJr
LEGO 1x1 Plate Vertical Clip 2555
LEGO 1x1 Plate Vertical Clip, part # 2555
- Pobrania
- 444
- Polubienia
- 11
- Ocena
- 5
Wszystkie modele
Liczymy pasujące modele…
P
PrintablesEdGJr
HSW Ratchet Hook
Simple, two-prong hook for HSW to hold ratchets, or in my case, a Yankee drill that's extremely top-heavy. Prints without supports. PLA at .20mm with 15% infill on a Creality K1C. Needs an “insert” to slide into.
- Pobrania
- 199
- Polubienia
- 39
- Ocena
- 0
P
PrintablesEdGJr
MG90S Servo Gears for LEGO
Smashed together the two designs to create a 24-tooth gear that is directly attachable to an MG90S servo. This allows for direct-drive of “things” instead of requiring adapters and incurring extra parts and axles. Printed at .1mm (larger…
- Pobrania
- 174
- Polubienia
- 14
- Ocena
- 0
P
PrintablesEdGJr
MG996R to LEGO Adapters
MG996R servos have a lot of torque, but if you have a lot of LEGO Technic stuff lying around, there's not a lot of options for melding the two. This is a collection of cut/paste/modify of a couple of different models to allow using those…
- Pobrania
- 59
- Polubienia
- 5
- Ocena
- 0
P
PrintablesEdGJr
LEGO(tm) Servo Gear 24T
Remix of my remix https://www.tinkercad.com/things/aOgR5YnQn9P-lego-servo-gears
- Pobrania
- 52
- Polubienia
- 5
- Ocena
- 0
P
PrintablesEdGJr
9G Servo Housing for LEGO
After many trials of other models, this one I've found to be very effective: not only does it hold the servo tightly (with M2 screws), but it also puts the main shaft in alignment with all other holes.
- Pobrania
- 37
- Polubienia
- 6
- Ocena
- 5
P
PrintablesEdGJr
Djed V1
The djed , also djt, is an ancient Egyptian symbol that is said to represent Osiris' spine. The hieroglyph represents “stability” (from Wikipedia ). As shown, printed in PLA at .20mm with supports! The statuette is a little over 5" tall…
- Pobrania
- 31
- Polubienia
- 2
- Ocena
- 0
P
PrintablesEdGJr
Adafruit Sensor Case with cut-out and LED blocker
Remix of small case for all 0.7 x 1 inch Adafruit boards, but with a “cover” on one end to blunt the effect of the LED power light. The other modification is to remove the center bar to expose any boards that have mid-mounted sensors that…
- Pobrania
- 23
- Polubienia
- 6
- Ocena
- 0
P
PrintablesEdGJr
SSD 1306 Frame
Simple frame/bracket to hold a small OLED 128x32 display. Pins out the back and a small dab of glue on the top to hold the screen. Note: some other models have been mis-labeled/tagged as 0.91" inch screens. Sadly, I have lost the origin…
- Pobrania
- 23
- Polubienia
- 2
- Ocena
- 0
P
PrintablesEdGJr
Taller Soundbar Riser
A basic soundbar riser that's a bit taller than others I found. This is intended to raise the bar (so to speak) above any “feet” that are holding the TV set and keep the soundbar level.
- Pobrania
- 21
- Polubienia
- 1
- Ocena
- 0
P
PrintablesEdGJr
HSW Nimbot D110 Holder
Mount your label printer for easy charging and use, all without taking it out of the holder.
- Pobrania
- 16
- Polubienia
- 3
- Ocena
- 5
P
PrintablesEdGJr
8 LED Ring Case with 2 Wires
Layer: 0.16 mm, infill: 15%. If you want to preserve the colors, use white or transparent filament (PLA is really good for this).
- Pobrania
- 12
- Polubienia
- 1
- Ocena
- 0
P
PrintablesEdGJr
PCA9685 Servo Board LEGO Technic Enclosure - slight remix
My board didn't quite fit, so just trimmed some more room for the servo connector side.
- Pobrania
- 6
- Polubienia
- 2
- Ocena
- 0
P
PrintablesEdGJr
MG996R Technic Mount
Mount your MG996R (or equivalent) into your LEGO Technic(tm) builds with this light-weight bracket. The intent was to craft something that is roughly the same size as a #64179 frame. NOTE : the shaft doesn't quite line up with the holes,…
- Pobrania
- 4
- Polubienia
- 2
- Ocena
- 0
To wszystkie aktualnie dostępne wyniki.