Liczymy pasujące modele…
They say this ‘hat’ can be combined with copies of itself and never produce a repeating pattern. Well, I haven't printed enough to confirm this… https://www.sciencenews.org/article/mathematicians-discovered-einstein-tile The attached…
I needed to Mount my empty Seadoo LinkQ fuel tank to my workshop wall to keep it off the floor. This model does just that. Printed with a 0.4 nozzle in PETG. I've included a .gcode file which shows how it was split. You may wish to add…
I have a PRUSA mk3S+ and finally the Raspberry Pi W2 became available so I can use PRUSA CONNECT. Needed a WebCam. Needed a mounting. I bought a Logitech BRIO 100. These parts mount it to the LACK Enclose leg. It retains some of the…
A short pair of stepladders are so useful around the house, especially in the kitchen with all those tall cupboards… But where to store them. The broom cupboard or plant room of course. but they need to be off the floor where they are in…
I took the original raspberry pi 2W door for the Einsy case and added radii to the slots.
If you print from the STL file I suggest changing the filament color as soon as land mass above sea level appears. I've already done this in the gcode attached. The z-axis (height above sea level) is exaggerated otherwise the island looks…
The LED strips fitted to the underside of the upper LACK table use double sided tape. I was concerned that temperature may soften the glue the the lights then fall. So I designed these clips to secure the LED strip and a pClip for the…
My builder needed an angled (45 degree) nozzle to apply sealant up into a roof capping. The thread is 25mm so a new nozzle was required.
This is a pair of lifting handles for the top section of a LACK Enclosure. The gcode prints in PETG. No Supports are required. The Print is orientated to give maximum strength in the lifting direction and has added perimeters to enhance…
I had two ASUS 15.5" note pad dispays which I needed to mount on an IKEA Stubberget twin screen mount. Neither displays had VESA mounts. This print provided that mount which I fixed to the back of each screen using double sided foam tape.…
I have some Scalextric models on a display shelf. I needed a display base that looks like tarmac. I printed this on a textured sheet.
I had a PI W2 plugged into my PRUSA mk3S+ but it didnt last long. I needed a seperate camera facility to monitor my prints. I had a spare Blink Camera that just needed a mount to my LACK enclosure. Here it is. Printed with 4 perimeters…
I saw these tetrapod shapes used in sea defenses and thought I would create something similar to prove to myself that I understood the geometry. Clearly I didn't as this is version 2… I imported the .stl to PrusaSlicer and split it…
It's time to hang your ironing board up in that cupboard. Print a left and right and glue them together. You'll need two assemblies. 0.4 nozzle and PETG
Whether you need an Air Scrubber for your 3D printing enclosure will always be up for debate but I consider it cheap insurance. So I have designed a unit that draws air out of the enclosure through a pair of 3M vapour filters and then…
So you've bought a ComGrow Filament Drier, melted a bunch of filament and concluded that all you really need is an airtight box and Silica Gel bags. But you need a carrier box for the Silica Gel pouches. What's more, when you put your…
I wanted an outside shower. The water needs an insulation jacket. Pulling the pipes through a 110mm diameter conduit pipes and using these printer spacers to locate the pipes optimally whilst foam filling the pipe when in position does…
Swing chair side trays never survive for long. People hold them to lift and move the chair and they break. That's what happened to mine. After much repairing they hit the bin. Here is a replacement tray that can fit inside or outside the…
I print with the filament in the drier box which sits on top of my LACK enclosure and needed to turn the filament through 90 degrees in a way that doesn't add any friction. That's what this does. Gcode files are for a 0.4mm nozzle. I've…
I needed a way of fitting my wakeboard onto my Thule roof bars. Because they are the slide out roof bars the Thule snowboard mounts don't fit. So I came up with this solution. The board is then secured to the roof bars with webbing straps…
Taking a video from the board of a water-skier is limiting if all you've got is a phone. Shaun Murray tested on on his YouTube channel some years ago and the video looked amazing. No details of the design though… How hard could this…
I moved my indoor MIRA shower outdoors but the plumber lost the lever… so i designed this knob to replace the lever. it sits in the same plane as the lever. You print two pieces and glue them together sandwiching the grub screw that…
I needed to repurpose an indoor shower head to go outside. My plumber left me a short length of 15mm plastic pipe out the wall and a straight fitting. I bought a flanged adapter to screw on the shower head which comes with a length of…
This is a box to house the components required to control a 4-wire fan used in my Air Scrubber project for my LACK enclosure. The information is displayed on a 128x32 OLED display. https://ebay.us/rxHI4i The control is performed by an…
End caps to mount the Fliteboard Li-ion charger to the wall. With limited bench space I had to mound my chargers on the wall. Printed in PRUSA PETG 0.2mm layer height and 0.4mm nozzle. The Gcode files have 220C filament and 75C bed as…
To wszystkie aktualnie dostępne wyniki.
