Liczymy pasujące modele…
Here is a selection of picatinny rails lengths from 40mm - 200mm stepping up in 20mm increments, you should be able to find one that suits the length you need. There are also 3 different end styles The measurements are to the screw…
This is a simple hex camo stencil, that can be used to spray paint or air brush. Its very flexible as its so thin but in the slicer you can change the scale on the z axis to make it stiffer. Take care removing it from the print bed as its…
Originally released in 2019 moving to printables Lepus Mk2 XT-TK (eXposed Trigger - Talon + Katana) Variant The Lepus is a fully custom designed Nerf blaster that is about as small as you can make it. It uses worker Talon mags and worker…
I needed an M-lok cover so made this hex pattern one, the pattern provides good grip. The width is 18mm length 80mm, I printed the one in the pictures at 0.28 height I would suggest 0.2 or smaller to give you a smoother finish.
Originally released in 2019 moving to printables WayMaker The WayMaker is a fully custom Nerf blaster shell designed to use the SUPERcore from SpectreArmaments (facebook). (The Snipercore should also fit but it's not been tested) The…
When I replaced my x-shot longshot plunger tube the turnaround was brittle and cracked, this will replace that turnaround, use the original barrel o-ring. It need a little bit of support when printing. I printed it at 0.2mm, 2 walls, 15%…
Rather than having to empty worker talon mags by hand this little tool can empty mags in record time. Its very simply to build requiring just 2 m3x8 cap allen screws (longer screws in the handle will bulge the wheel and cause rubbing).…
I Made a more comfortable charging handle, its shorter than the original one on the BK1s or BK2s. To install it remove the original charging handle and use the screw to fit this new one
This part strengthens the thin plastic barrel position lips on the BK1s / Bk2s shell or if the these lips have broken then the part with the raised section can replace these lips.
This is an improved version of my original bk mag https://www.printables.com/model/1219069-bk1s-bk2s-magazine-short-10-dart-12-dart-max I have multiple lengths for different print bed sizes 180mm, 220mm 250mm. Only 180 has been tested due…
I've had 370 sized motors hanging around for ages waiting to be put into a blaster but I never quite found the right one to put them in. Some 370 motors are pretty powerful and would serve as good alternatives to some of the hobby grade…
I got annoyed with the original Kunlun mag release that as you pull the mag out it jammed up as you need to push the mag up into the magwell for the lever to release the mag. I have made a release that pulls horizontal so no more jams on…
The ‘dart picker upperer’ is a tool i've been developing for years to make the perfect tool to help pick up darts while in a standing position, its mouth width has been perfectly tuned to allow you to easily push it over a dart and allow…
I wasn't sure about cutting up my BK shell for a talon mod, so designed a magazine. I have an Bambu a1 mini so this mag is the limit of print bed size, it uses a talon spring so easy to get hold of. I've made multiple revisions and tweaks…
This dart fork is designed to make it easy to pick up nerf darts from the floor, using grid design of the prongs means that the darts can be picked up from different angles, so it's easier to just prod the dart without having to align it…
Ever build a flywheel cage and then totally forget its crush down the line? I made this gauge to fix that! Now you can easily measure the crush of any flywheel cage whether it's installed or not, so no more trying to measure 0.5mm by eye.…
To wszystkie aktualnie dostępne wyniki.
