Liczymy pasujące modele…
If the X-axis cable should break it will do so in a place where you can't solder a new wire to the broken one. It will be almost inside the stepper. With this very simple solution, the cable (if it should break) will do so outside of the…
I needed a place to hang my pliers. so less clutter.
It is always difficult to measure a radius of a rounded corner. This way you can better guestimate it. Print instructions Print with text side down for better result.
A table stand for my mixer. this way I can see all the controls at a glance and from a distance. you can loop the cables under the beam to keep it a bit tidy. Use some force to clamp the parts together. It's a tight fit.
A stand for my Weller WSP80 soldering iron. you may have to stick some weight to the bottom. Although it will do it's work as is. No supports needed. Print instructions no support needed
This is for the DX-Commander 10m long 6 band antenna. Sometimes when the wind bends the antenna, the wires get caught behind the jubilee clip, and really mess up the SWR. This spacer prevents that from happening. It goes on the 3rd pipe…
A nice way to lay down your tenor sax without the keys touching the surface. Now the sax lays on the edge of the bell, the bend, and the stand. The stand gently clips around the neck. You can pick up your sax and then take off the stand.…
A stand to place your TS80 soldering iron. I will be very stable as is, but you can weigh it down with some heavy stuff stuck to the underside. I used a sheet of thick lead. The .stl doesn't represent the correct bed orientation. Sponge:…
Hi, This is a box for a li-ion 18650 and an ESP8266. You can leave the 8 pin header on the board. There is a switch on the box and a 3.5mm stereo jack for in/output. there is a charge input for the 18650. I use this for a DS18B20 to…
Hi, An enclosure for the Nano VNA V2. With a holder for the open, short, load and barrel connector. under a lid. The stylus has it's own place too. It can be used to take out the SMA connectors. If you have some transparent filament left…
print top on flat top part. no supports print bottom on flat bottom...... Print instructions print top on flat top part. no supports print bottom on flat bottom......
A TS80 portable "wireless" soldering iron stand for use with black and decker batteries. The orange and black battery is a original one, the big one is a cheap knock off (40 Eur.) Super handy for use in the field. The battery clip can be…
a stand for the RT series (WMRP series) soldering iron. can hold 2 extra tips. If needed, weigh it down with some steel or lead sheet. Sponge: search for T0052242099…
This is a raspi zero camera housing with wall / floor mount and ball pivot. it is made for the small camera modules. do not use the sticky tape on the camera flex foil, everything fits snugly. do not melt the pins inside the holes of the…
This is a spacer which fits the 10 m high antenna. It is function is to hold the driven plate nicely parallel to the ground plane plate. Without it the driven plate can get a bit slanted and that can vary with the wind pushing on the…
A 2U fan back panel for your home lab rack. This version fits your I3 when printing with no skirt. Had to redraw it because my PRUSA didn't understand imperial :-D. This design came from https://github.com/JaredC01/LabStack .Look him up,…
A table stand for a Yamaha MG06 series mixer. The space between the "hooks" is 26mm so if your mixer is the same or thinner, it will fit. Tthe connections are friction fit, so you have to use a tool to press them together. see picture.…
Hi, This is a frontpanel for the EU1KY VNA mounted in a TEKO 115.5 enclosure. I didn't like the aluminium plate and I couldn't fit my battery inside. Now there is ample room for fitting batteries, I opened a power bank (carefully!!!) and…
A stand for the N1201SA vector impedance analyzer.
This is a 10 inch rack mount bracket for 4x 2.5 inch SSDs , designed for homelab, NAS or Raspberry Pi rack builds . The mount fits standard 10″ racks and allows easy airflow and cable management. I sneaked a holder for a USB dongle in…
This is an interface plate to put your XPA125B on top of your Icom IC-705 if you already have a Windcamp protective shield . a stand in the back of the xpa125 will hold it in the same angle as the 705. There is also a little enclosure…
A front panel for TP-Link TL-SG108 with an extra keystone connector. This is a front panel only. so there is a metal shelf underneath. Clamps are used on the back to secure the TP-Link switch to the shelf. Power supply cable notches on…
This is a mast enclosure for a Meshcore repeater, or something else. A Heltec V3.x will fit and there is a special place for a 14500 li-po battery the usb port is accessible. so you can power the device from a solar panel or just 5V from…
Handheld case for a wireless ham radio PTT button (HM-10 Bluetooth, no microcontroller needed inside). Pairs with my ESP32 firmware that sends your callsign in Morse code automatically. There even is a MQTT link present, because who…
To wszystkie aktualnie dostępne wyniki.
