Liczymy pasujące modele…
This is based on a Leviton plate with correct offsets and set-backs. Print Settings Printer Brand: Anet Printer: A8 Rafts: No Supports: No Resolution: 0.20 Infill: 16 Filament: Inland PLA Red Category: Decor
The wife wanted a cactus decoration... Print Settings Printer Brand: Anet Printer: A8 Rafts: No Supports: No Resolution: 0.20 Infill: 10 Filament: inland PLA green Category: 2D Art
Stick this in your nose and have a new look ;) Thin for giving to kids for Halloween - resize to fit if you need one.
My rubber bleeder caps were missing so I made these. They fit over 0.3" brake bleeder fittings (looks like a common size to me). Print Settings Printer Brand: RepRap Printer: Prusa i3 Rafts: No Supports: No Resolution: .2 Infill: 100…
Made this for wife to continue decorating for Easter Scale the model for your printer. I have a 310mm bed. In prusaSlicer I chose the 'fill print volume and that worked well for X and Y. I forced Z to 3mm
My lead screw nut center is 22mm away from the printer arm. The motor mount is 21mm (42/2). I designed this mount to make the stepper shaft line up true vertical. The other requirement was to use the same screws that the original mount…
I cracked a knob on my old Tek TDS220 scope so I made this. It is a tight fit. It might work on yours too. Print Settings Printer: Anet A8 Rafts: No Supports: No Resolution: 0.1 Infill: 11 Category: Electronics
I wanted a better endstop for the Aquila that gives me the full width of the bed that prints without supports. There may be a little stringing from the bridging, but it will be inside. Also the connector has better access with more room…
I needed a case for a blu-ray disk that I got without a case... Print Settings Printer Brand: Anet Printer: A8 Rafts: No Supports: No Resolution: 0.2mm Infill: 15 Filament: Inland PLA blue Category: Organization
The mainboard fan on the Aquila is loud! I designed a new cover and am now using an 80mm 24V fan. I added another stl with thicker walls and a mount point - slide to get it to fit. These fit Aquila and Aquila C2 (maybe others) As a side…
Simple decor for Easter - no special instructions.
Now that the monsoons have moved in, using a cork coaster just gets wet. This coaster will catch the condensation and allow for easy dumping.
I needed a small stand to hold ink cartridges. So, I used onShape to design this one. One model is for 6 and the other for 12. I added one more model that will hold 6 cartridges and one Pilot brand 12pak box in the back. Print Settings…
Simple decor at Easter to match simple Christmas manger scene. Added .step file as well as .stl
I got a new A8 that has tighter clearance around the buttons. The old button trim was too large and since the buttons taper, I can't get any clearance at the back of the Button faceplate. So, I made a shallow trim to keep the buttons…
Customized version of http://www.thingiverse.com/thing:1220978 Created with Customizer! http://www.thingiverse.com/apps/customizer/run?thing_id=1220978 Instructions Using the following options: name = Laura font = 0 thickness = 5…
Make 2 halves to get a whole ;) Uses support for attachment feature. Make thinner/thicker as desired. I used it in our AZ home for bathroom door decor.
I got the hth swimming pool water test kit and it comes in a thin plastic clamshell. It became a 3D project! Print Settings Printer: Anet A8 Rafts: No Supports: No Resolution: 0.32 Infill: 16 Filament: inland PLA green Post-Printing…
Instead of my brother's dog tags (non-service) just laying around. I decided to make a little memorial so they could have a resting place and sit on the counter with other family mementos. I looked on Thingiverse and other places but…
A simple bumper to replace the ones missing from my Vostro 3700 laptop. Print Settings Printer Brand: Anet Printer: A8 Rafts: No Supports: No Resolution: 0.1 Infill: 88 Filament: inland TPU Blue Category: Replacement Parts
This tool helps to get a little more torque on the plug in the pool deck to remove it. I found it also works on the bottom of my salt shaker with a similar finger grip! Print Settings Printer Brand: Anet Printer: A8 Rafts: No Supports: No…
I got some of these cheap voltmeters: https://www.gearbest.com/development-boards/pp_134717.html?wid=37 and I made an enclosure for them. I saw that other meters on the website (…
I got a direct drive for my Jayo S8+ (sunlu brand). It triggered the X end-stop too early so I designed this to give me access to the full X. Uses same screws as original.
Instead of throwing loose battery packages disorganized into the fridge door, I made a custom holder to hold them in place. The battery package width is 50mm. I added a holder for batteries from Amazon Basic - these are 45mm and come 10…
This was designed for a Magic Chef oven, but there are more it fits. Print Settings Printer: Anet A8 Rafts: No Supports: Yes Resolution: 0.2 Infill: 33 Notes: The support was only needed for the screw hole offset. Category: Replacement…
If you get one of these flying orbs, print this stand. It will come in handy while charging or just displaying. I printed with .4 nozzle and matte PLA with a 'fuzzy' outside wall painted on in prusaslicer.
I have an outdoor built-in grill (Turbo by BBQ Galore) and one of the valves developed a leak. I could not find a gasket locally so I ordered TPU filament and designed this gasket. It worked fine. Print Settings Printer Brand: Anet…
Dairy pod holder with a cutout for pods with a spout. Added chamfer to enforce legs. Added a 'taller' version to hold half-half from another vendor. Print Settings Printer Brand: Anet Printer: A8 Rafts: No Supports: No Resolution: 0.24mm…
This replaces the DC coupler cover embedded into the battery cover of the Canon PowerShot S400 camera I used PLA .125 layer
To wszystkie aktualnie dostępne wyniki.
