Liczymy pasujące modele…
I really liked jeoje's design for the Playseat Challenge, but I didn't have any M3 hardware that was long enough. I had some M6x40mm flat head screws leftover from another project, so I decided to use those instead. I started from scratch…
Update (9/19/22): Uploaded a revised base with a thinner clip after some feedback that it was too wide. Update (7/11/22): I added the STEP file since someone requested it to make changes to the original. I was a big fan of the…
After using the original to hold drinks, I noticed that the joy cons had a tendency to slide out of the rails due to the weight of the beverage. So instead of trying to modify the original STL, I figured it would be easier to just model…
Update 8/9/22: Added STEP files for anyone who would like to more easily modify the design. I liked the original but I found that it would bind up occasionally. I thought a bearing would help keep it smooth. I have a ton of 608 bearings…
After the pandemic started and I began WFH, I bought a cheap desk. The drawers did not come with any handles or knobs! You're supposed to grab it from the side, which I found kind of annoying. Naturally, I solved this issue with 3D…
1/10/2022: Rev C Added another version of the compression limiter bushing spacer. Has a hole diameter of 8mm as requested by a Thingiverse user. 8/17/2018 Update: Modeled the OEM spacer that is used on the VW Touareg and other vehicles,…
My take on the popular KitchenAid mixer attachment holders. Can be attached under your cabinet using a 3M Command strip or a #8 flathead wood screw for a more secure installation. I've used PLA and PETG with no issues. Supports are…
I liked the form of the original dock and being able to add weight to it from the bottom really makes using the dock easy (can't knock it over easily, etc). However, I did not like using set screws to hold the magsafe pad in place. I…
Remix of another hood latch pull. Remodeled it so that it's easier to print. Also ended up making it slightly shorter, but is still long enough to pop the hood. Category: Automotive
Update (2/26/21): I've uploaded V3 files. These are similar to the previous version, but the main shaft is hex shaped versus the older "D" style shaft. I noticed that the D style would develop slop in the pawl, so turning the knob to…
These are replacement gears for the headlight adjuster mechanism on my B6 A4 with bixenon headlights. The gears often break or strip leaving you with no way to adjust the aim of the headlights. The assembly shown is for the up and down…
A common issue with the projectors in OEM Valeo Bixenon housings fitted to B6 A4's is that the reflector bowl can become scorched which results in diminished light output. Instead of replacing the whole headlight housing, only to have the…
Recently got a new MacBook Pro (2021) and noticed there was no good way to wrap the cord around the power brick. Naturally, I looked to see if there was anything already made for my charger (Model A2518). I couldn't find any that would…
I want to preface this with the fact that I never had a chance to personally test this in my own vehicle. It was a project that I started circa 2017, but never got around to finishing it. I'm simply sharing the files since some people…
This was something I custom designed for myself and is pretty unique to my remote control collection. But when the Remote Holder contest opened I figured it couldn't hurt to enter! The remotes that fit this holder are for a Samsung TV,…
Print on it's back. Simply remove one of the top screws on either side panel to mount. I derived this from Erik's wonderful design, but I only have three print cores total so six slots was more than I needed. I simply edited the STL by…
Overview: These are pieces that I designed to repair a friends cargo cover on his Audi A4 Avant (B5). I'm not sure how common this exact failure is but I figured I'd share it in case it helps someone from throwing out their cover and…
Use most current revision STL file, rev B. When installing a "cold air" intake on Audi/VW vehicles equipped with secondary air injection (SAI), the inlet hose to the pump needs a filter since it normally connects to the factory airbox…
I needed a MagSafe compatible mount for my Proclip, I figured I could make something with the magnets I have leftover from other projects. Sure enough, I found Uko's design and used it as inspiration for this design. I didn't want to rely…
Designed this replacement since I accidentally bought a tote that was missing a handle. Didn't want to go back to the store and deal with an exchange, so I just designed and printed another! Fits all Sterilites totes this size (15qt/14L),…
The original is sized for a 44mm Apple Watch. I have a 38mm Series 3, so I modified the cutout so the watch sits nicely in the dock. I also removed the magnet pockets and changed over to M3. I used special Torx head screws for threading…
To wszystkie aktualnie dostępne wyniki.
