Liczymy pasujące modele…
For a Jeep or the bathtub! Supports only necessary on the beak! If you enjoy this, like, comment, make, or check out my other models: https://www.printables.com/@BuckyKatt129 Happy printing!
The Porsche 918 Spyder is a hybrid supercar unlike any that you have ever seen. This plug-in hybrid sports car is designed to maximize both efficiency and power, two elements that typically come at a cost to one another. Print your own…
This is a multicolor American Flag that can be printed on any printer. Simply swap between white, red, and blue. Each color swap is exactly .4 mm apart. The following settings are for .2 mm layer height. Start with white Swap to red at…
This is a simple little print for your cat so that it will not have to rub up against your leg over and over and over again, but can still scratch itself. You can also set it on the ground where it can roll and roll it with your foot.…
Print Settlers of Catan Pieces -- all of them or just one!
I would recommend printing in grey, a filament swap at the top to white if you want to. If you like this, check out some of my other models here: https://www.printables.com/@BuckyKatt129 Happy printing!
The Nissan 350Z, often simply called the "Z," is a two-door sports car that was produced from 2002 to 2009. Known for its distinctive design, the 350Z features a sleek, low-profile body with a long hood and a short rear deck. Under the…
Print in gray, sharpie the eyes black, add a backdrop, and done! Please leave a comment or make! Happy Printing!
The Mazda Miata ND, also known as the fourth-generation Mazda MX-5, is a sleek and stylish roadster that perfectly blends classic charm with modern performance. Introduced in 2015, this iconic sports car is celebrated for its lightweight…
This is a design that's been in my head for a while, and the pet supplies contest on Creality made me decide to do it. It is set up to be completely powered by gravity; just put your cat's food in the Mason jar, screw the base onto it,…
If you have lost a Carcassonne piece, or just want a new color, look no farther! If you like this, check out some of my other designs here: https://www.printables.com/@BuckyKatt129 Happy printing!
The Pontiac Vibe is a compact hatchback that mirrors the practicality and versatility of its sibling vehicle, the Toyota Matrix. Produced from 2002 until 2010 by the joint venture between General Motors and Toyota, the Vibe inherits…
Print in white, sharpie the eyes black, add a tasteful backdrop, and done! Please leave a comment or make! Happy Printing!
Print in gray, sharpie the eyes black, add a tasteful backdrop, and done! Please leave a comment or make! If you like it, here are some of my other models: https://www.printables.com/@HudsonPrnt9_2394607/models Happy Printing!
Print your very own Giant Nut! Compatible Golden Bolt coming soon! Please leave a comment or make! Happy printing!
Beater Bar Drum Spinner for unused motor that actually spins scarily fast. I took my motor from a Nerf Hyperstrike Elite, but you can cut or redesign the hole to your own sizing. Wire the motor through the hole in the left side to 2 AA…
Just saw some comments asking for this; used Cura to split and export the file. The original model was great, but I would rather print this seperately Happy printing!
https://cults3d.com/en/3d-model/gadget/pantograph-knife Here is the original model by _JENSEN. I thought it needed a little something more. Just clip this onto your waistband and slot the knife onto it. Pull the knife up to remove it.…
For Multicolor, simply swap color one layer after the text starts. Made fully in TinkerCAD Please like, comment, make, or follow! Happy Printing and Roll Tide!
An evergreen/Christmas tree with minimal supports Please leave a comment or make! Happy printing!
This is a pretty simple model to print and enjoy if you know what you're doing; just print the center block first, and then pause the shell printing right before it starts the top, while it is still open. Put the center block in the…
Please like or comment This is actually another edition of my motorized model, but no overlap in the pieces If you liked my last model but don't have the motor for it, don't worry! 99% 3D Printed; uses only a rubber band for power Print…
Print up to the bottom of the text in a contrasting color, then swap (using MMU/AMS or a single extruder filament swap) to another color for the rest of the mug. Something like white and black contrast would be preferrable. Normal…
Show your support for Hudson Printing Industries with this stunning two-color plaque! No AMS/MMU required! For the inverse (background is taller) swap filament at layer 11 if using .02 mm layer height. I recommend using a lighter/brighter…
A Logo/Keychain for the UK brand Tentsile. Created completely from scratch on TinkerCAD Please like, comment, leave a make, or follow. Happy printing! If you like this, check out some of my other models:…
I only have an air hose and no screw/press fittings so i modified the cylinder head a little bit
To wszystkie aktualnie dostępne wyniki.
