Liczymy pasujące modele…
This is a tray-mount 60% keyboard case. It is a remix of the following model: KeyBoard Case for Mechanical KeyBoard (Pok3r, GH60, Satan) by MaxWinterstein. (See the "Remixed From" section in the sidebar to the left for additional…
INTRODUCTION: This is a gummy worm-mount case for the CIY Tester 68, an excellent barebones keyboard kit that can be purchased for about 12.50 USD on Taobao (excluding shipping). It is great in its stock form, and is also a great platform…
This is a tray-mount case for 60% keyboards. It is a remix of two models: A free 3d office keyboard model that I found online but can no longer locate to provide attribution. KeyBoard Case for Mechanical KeyBoard (Pok3r, GH60, Satan) by…
This is a modular, interlocking system for storing deskmats. The top bracket is meant to be hung over a cabinet door, followed by the desired number of middle brackets, and then, finally, the bottom bracket. The brackets are designed to…
This is a wide-bezeled 60% keyboard case with the following features: Standard 60% size (e.g., GH60, DZ60) -- The dimensions of the interior tray compartment track the size of a typical 60% plate (i.e., 285.752 mm x 95.252 mm). Note that…
NOTES FOR PRINTING: I would recommend printing out this model upright, to eliminate pixelation along the curves. Also, you can try placing dampening material on the bottom of the case. It is easier to do so with this case because there…
This is a tray-mount 60% keyboard case. It is a remix of the following model: KeyBoard Case for Mechanical KeyBoard (Pok3r, GH60, Satan) by MaxWinterstein. (See the "Remixed From" section in the sidebar to the left for additional…
INTRODUCTION: This is a kit for converting any standard 60% tray-mount keyboard (e.g., GH60 or DZ60) into a taco bumper gasket-mount keyboard. It consists of (1) the case and (2) gasket wings, which clip onto the plate. The gasket wings…
This is a tray-mount 60% keyboard case. It is a remix of the following model: KeyBoard Case for Mechanical KeyBoard (Pok3r, GH60, Satan) by MaxWinterstein. (See the "Remixed From" section in the sidebar to the left for additional…
This is a tray-mount 60% keyboard case based on the F62 Model F keyboard. It is a remix of the following model: KeyBoard Case for Mechanical KeyBoard (Pok3r, GH60, Satan) by MaxWinterstein. (See the "Remixed From" section in the sidebar…
This is a tray-mount case for 60% keyboards based on the Commodore 64. I call it the Lionel because it's a fraction of the size of a full Commodore 64. It is a remix of two models: Commodore 64 model…
This is a replacement rotary encoder knob for the TM680/TOM680 keyboard. There are three different versions: regular cylinder, filleted cylinder, and chamfered cylinder. The knob's outer diameter is approximately 19.5mm, and the stem…
This is a tray-mount 60% keyboard case. It is a remix of two models: Teardrop model that has apparently been deleted from Thingiverse. KeyBoard Case for Mechanical KeyBoard (Pok3r, GH60, Satan) by MaxWinterstein. (See the "Remixed From"…
This is a tray-mount 60% keyboard case. It is a remix of two models: Art Deco Style Box by NordwickDesign. KeyBoard Case for Mechanical KeyBoard (Pok3r, GH60, Satan) by MaxWinterstein. (See the "Remixed From" section in the sidebar to the…
INTRODUCTION: This is a kit for converting a 60% tray-mount keyboard into a taco bumper gasket-mount keyboard. It will work with (1) any standard 60% plate and PCB (e.g., GH60 and DZ60) or (2) any 60% plate and PCB with five 1u keys in…
This is a tray-mount 60% keyboard case. When printed in translucent material, it allows the light from an underglow PCB to shine through more easily. It is a remix of the following model: KeyBoard Case for Mechanical KeyBoard (Pok3r,…
The stock Wowstick base allows the screwdriver to easily topple over. This replacement base remedies that deficiency. The model is posted in both 3MF and STP formats.
This is a tray-mount 60% keyboard case. It is a remix of the following model: KeyBoard Case for Mechanical KeyBoard (Pok3r, GH60, Satan) by MaxWinterstein. (See the "Remixed From" section in the sidebar to the left for additional…
This is a tray-mount 60% keyboard case. It is a remix of the following model: KeyBoard Case for Mechanical KeyBoard (Pok3r, GH60, Satan) by MaxWinterstein. (See the "Remixed From" section in the sidebar to the left for additional…
This is a tray-mount 60% keyboard case. It is a remix of two models: The 4 Types Art Deco Lightswitch Cover Decorative Frame Backer by IvyEpsilon. KeyBoard Case for Mechanical KeyBoard (Pok3r, GH60, Satan) by MaxWinterstein. (See the…
INTRODUCTION: This is a kit for converting any standard 60% tray-mount keyboard (e.g., GH60 or DZ60) into a taco bumper gasket-mount keyboard. It consists of (1) the case and (2) gasket wings, which clip onto the plate. The gasket wings…
This is a "negative" block used in the design of standard 60% tray mount keyboard cases. It is used to subtract a tray cavity/well from your case design. The PCB/plate will rest inside the tray that you have carved out using the block. (I…
This is a gummy o-ring mount case for the CIY Tester 68 keyboard. I have uploaded the whole case, as well as the case in six parts, in OBJ format. (The whole case is approximately 365.06 x 174.74 x 64.33 mm.) Finally, I've added the base…
This is a beagle lamp, with a compartment at the bottom to accommodate the following remote-controlled LED light (or one like it): https://www.aliexpress.com/item/32983679031.html?spm=a2g0s.9042311.0.0.5da44c4d7snB4o The face has a line…
INTRODUCTION: This is a kit for converting 60% tray-mount keyboards into a taco bumper gasket-mount keyboard. It will work with (1) any standard 60% plate and PCB (e.g., GH60 and DZ60) and, alternatively, (2) any 60% plate and PCB with…
This is a tray-mount 60% keyboard case. It is a remix of two models: USB Park Peacock by Longmans_Bro. KeyBoard Case for Mechanical KeyBoard (Pok3r, GH60, Satan) by MaxWinterstein. (See the "Remixed From" section in the sidebar to the…
This is a tray-mount 60% keyboard case. It is a remix of the following model: KeyBoard Case for Mechanical KeyBoard (Pok3r, GH60, Satan) by MaxWinterstein. (See the "Remixed From" section in the sidebar to the left for additional…
This is an abstract 60% keyboard case with the following features: Standard 60% size (e.g., GH60, DZ60) -- The dimensions of the interior tray compartment track the size of a typical 60% plate (i.e., 285.752 mm x 95.252 mm). Note that the…
This is a gummy o-ring mount case for the CIY Tester 68 keyboard. I have uploaded the whole case, as well as the case in six parts, in 3mf format. (The whole case is approximately 431.67 x 208.98 x 140.71 mm.) Finally, I've added the base…
This is a Bauhaus-inspired 60% keyboard case (which apparently violates most of the principles of the Bauhaus movement). The case allows for either tray mounting or ring gasket mounting (using the technique described by HugoKeys in this…
INTRODUCTION: This is a ring gasket mount case for the Hexgears GK707 keyboard. INGREDIENTS: Hexgears GK707 plate and PCB 5mm diameter gasket material (e.g., silicone) for the top part of the case. A length of about 350mm should be…
This is a revision of an earlier case posted here: https://www.thingiverse.com/thing:4823463 I found the original edges of the case too sharp, so added chamfers to reduce the risk of laceration. Category: Electronics
I use a GK61 mechanical keyboard as a travel board with my 2011 MacBook Air. I found, however, that when resting the GK61 on top of the MacBook, the rubber feet on the bottom of the GK61 would press down on and activate the MacBook's…
This is a "subtraction" block used in the design of standard 60% tray mount keyboard cases. It is used to subtract a tray cavity/well from your case design. The accompanying standoffs will sit at the bottom of the tray, and will support…
I have been trying to sculpt an interesting keyboard case design, but, despite my best efforts, each and every one of my designs has broadly fallen into one of three categories: (1) ergonomic pillow; (2) horseshoe crab; and (3) molar.…
INTRODUCTION: This is a replacement gummy worm gasket-mount case for the Kananic 82 keyboard. I designed it around the high-profile version. I am not sure whether it will work on the low-profile version. In light of the CIY68, FL Esports…
I have been trying to sculpt an interesting keyboard case design, but, despite my best efforts, each and every one of my designs has broadly fallen into one of three categories: (1) ergonomic pillow; (2) horseshoe crab; and (3) molar.…
INTRODUCTION: This is a ring gasket mount case for the Teamwolf Zhuque keyboard. This version has rear side cutouts. Another version has front side cutouts. INGREDIENTS: (1) Teamwolf Zhuque plate, PCB, and cord. (2) ring gasket material…
This is the penrail version of the case posted here: https://www.thingiverse.com/thing:5000228 The penrail I used can be found here:…
INTRODUCTION: This is a ring gasket mount case for the Teamwolf Zhuque keyboard. This version has rear side cutouts. Another version has front side cutouts. INGREDIENTS: (1) Teamwolf Zhuque plate, PCB, and cord. (2) ring gasket material…
To wszystkie aktualnie dostępne wyniki.
