Liczymy pasujące modele…
Echo 4 Foot, Bracket Needs a Photo-camera screw, 1/4 "- 20 UNC 8-12 mm long, which is installed in ECHO 4. Print Settings Printer Brand: Creality Printer: CR10S PRO Rafts: No Supports: No Resolution: 0,16-0.20 Infill: 30 Filament: Sunlu…
Wrapping paper cutter with an ordinary Snap-Off Utility Knife (9 mm) Bring the paper cutter flush with the roll, gently press together so that the blade goes through the paper and simply pull (push) along the roll. The blade is easy to…
Self tensioning and clamping in one, no Winkles, always smooth For short stick, cut the sandpaper to a length of 230 mm and a width of 12 mm For long stick cut the sandpaper to a length of 280 mm and a width of 12 mm Also goes as a nail…
This is a Collection of Cable Tie Holder and Velcro Strap For Screws or Double-Sided Adhesive Tape. Chamfer down and standing printing.
Battery dispenser for two sizes, AAA and AA , fast printing in three hours (0.28 mm layer height). Requires three screws diameter 3.5 mm 15-25 mm long , or sea head M4 X 15-25.
Anti-moisture silica gel container Fast Print possible due to straight pattern. In two versions. Important, before the first assembly, a little grease the thread. The silica gel should be larger than 2.0 mm because the holes are 2.0 mm.…
Anti Moisture Silica Gel Box (container) Easy to print and easy to close. In three versions. Important, Grease a little before assembling for the first time. The silica gel should be larger than 2.5 mm, as the holes are 2.5 mm. Diameter…
Blink Outdoor X2 camera protection rain Rain cover and protection, for the original bracket. Easy, just take off rain protection and remove the camera up to the battery change. Be needed: 2x m3x20mm 2x M3 nuts Alternatively, wood screws…
Battery dispenser for two sizes, AAA and AA, to plug together and whoever likes a drop of glue.
Toothpick Dispenser For toothpicks with a diameter of 2–3 mm and a maximum length of 68 mm .
Sanding stick Round with self-clamping cut the sandpaper to a length of 100 mm and a width of 34 mm For threaded parts always in Cura Set Slicing Tolerance to Exclusive, the setting can be found under Experimental. In other slicers, or if…
Anti Moisture Silica Gel Box hexagonal (container) Easy to print and easy to close. In three versions. Important, Grease a little before assembling for the first time. The silica gel should be larger than 2.5 mm as the holes are 2.5 mm.…
For 17 mm wide folding ruler. Grease a little before assembling for the first time. Supports: No Resolution: 0,12 - 0,16 Infill: 30
Bracket for ratchet straps, universal for curves, flat, or edges. Blink outdoors X2 ball head bracket with rain protection. Simply, take the rain protection off and take out the camera to change the battery. To be needed: 1x M4X10-15 mm…
For the original blink camera bracket and the supplied screws, or M3 with nuts. It is for Tension Ratchet Straps Fastening. To attach to round, angular and flat surfaces on
Echo Dot 4 Generation (100 mm diameter) Fasten with double-sided adhesive tape approx. 1.5 mm thick (two to four layers) in the middle. Print Settings Supports: No Resolution: 0,12 - 0,16 Infill: 25 Category: Household
USB Cable Organizer Plugs are spared because attached to the cable. Easy hanging. For cable diameter 3.0 -3.8-4.0-5.0 mm Cap can be printed in different colors, for different types of plugs. USB holder for 2-3-4 cables
USB cable organizer with magnetic holder Stop in front of the cover layer, (Pause at height) It is used: magnets in diameter 10 mm height 2.5-2.6 mm Diameter cable from 3,5–4,8-5,5 mm
Universal bracket for binder clip 25 mm wide Screwable.
Doorstop with hanging option for door gap height of 4 mm to 14 mm. It is best to print with TPU because flexible, and not slipping, gently for the door.
Cling film holder With Cura Slicer (print thread), adjust to (experimental) slicing tolerance to Exclusive.
Spices and herbs signs Can simply be reduced or enlarged (scaled) Filament change at Layer 7 (Resolution 0.20 mm) Thyme, Oregano, Basil, Chili, Mint, Parsley
Lint roller inner diameter 37.5-38 mm e.g. IKEA BÄSTIS or on Amazon, Temu for almost all lint scooters. Without supports For threaded parts always in Cura Set Slicing Tolerance to Exclusive, the setting can be found under Experimental.
To wszystkie aktualnie dostępne wyniki.
