Liczymy pasujące modele…
Replace the LR1130 with a AAA battery for the QST express caliper I got from Aliexpress. the battery is fiction fit with the bend on the side of the battery compartment. You will need: wires, tinfoil, some type of glue and a multimeter…
Portable(?) 6 pair of earbuds storage case or tray for those into tip-rolling. The pillar is 5.3mm, each bud space is 15mm. Size is 96x36x12mm and 93x33x9mm for box and tray respectively. The tolerant between the container and the cap is…
Compact but not so compact version of the switch dock. Not really happy with the other dock out there so here is my take on it. Require 4 parts. "dock", "top cover", "enclosure" and "bottom plate". The mirrored version have the USB-C and…
This has 5 parts: the Switch mount, the controller clamp, the arm (the one in photo is the 40mm) and 2 bolts. Mount and clamp need supports, try to not add supports at the clip part of the clamp. Features: High degree of freedom movement…
I like the wind path from the high performance toolhead cover and easy debugging of the magnetic removal toolhead cover and mash them together. Important: I find this model too unsecured when connected via magnet and decided not to use…
A compact case for LD2140B, LD2410C or LD1115H human presence detection sensor with BH1750 light sensor and GY-BME280 Temperature/humidity/Air pressure sensor A wemos D1 mini or S2 mini will be needed as the main board. Features:…
This will only fit variable resistor with the stem of 5.8-6mm thick Spec: Knob height: 12mm Outer diameter: 17mm Outer shell wall thickness: 2mm Inner stem diameter: 6.15mm Inner stem wall thickness: 2mm Outer shell and inner stem height…
This is a Work in progress!!! I'm still testing it myself This is an oldham alternative based on HevORT Wobble Rings and try solving Z wobble/Z banding. Reason this exist was because I don't have some require parts for the other wobble…
180mm aluminum bed is cheaper and easier to come by than the the Voron 0 bed. I got this for around $8 from Taobao that comes with heating elements and thermostat and an extra spring steel bed sheet for another $6. Extra wire harness file…
I'm really forgetful, so this visual cues is to notify me to take the rubbish out using Esphome and Home Assistant. 2 bins to the side for general wheelie bin and recycle bin, the middle cone is just a visual cues for other home assistant…
A simple box for the 22 piece amibo card i got from ebay. Tolerant is very close. Depends on your printer, you may or may not need some sanding. My print required some at the corners. Category: Organization
This is a upgrade part for Titan Aero All Metal Extruder, the all metal version of the E3D titan extruder clone. Adding it to use flexible (TPU) filaments in bowden extrusion configuration and maybe (probably don't need) direct drive.…
The Spacer is for 4 longer screws so it don't come out from the other side of the mount. I used 4mm M3 with the 1mm spacer, If you have 3mm then it should be fine without it Requires: 2x 6/8mm M3 2x 3/4/5mm M3 Don't over tighten the screw…
Uses the optical sensor to detect filament. require: 2x10mm M3 screw and 2xM3 Heated inserts I design it for the bowden bondtech bmg extruder. If mounting directly to 2020 extrusion then longer screws and might not require heated inserts.…
Adapter mods for 2 of the my wired mechanical keyboard to removable cables. Teamwolf ZhuQue 87 keys Unknown brand 96 keys. Model GM221 Update 2022/12/06 Add an adapter for the Teamwolf Voidray+ mechanical keyboard Update 2023/01/10 Add an…
Will require 2 slightly longer or same size screw for fan shroud, 2 for the TAP and 2 heat insert Print 2, 1 in mirror mode Might fit the Chaoticlab's CNC TAP, however, I don't have one for the test fit.
Don't think much people have that hotend but figure I should put it out there, the extruder screw hole no longer fits Sherpa/HGX or sailfin extruders and will only fits the orbiter V2. This is for the 3Dsway's CH-C volcano hotend with…
Features: Holds 18 28mm or shorter bits (+1 with screw driver), design with 3mm holes at bottom to slot-in magnets if bit become too loosen. Hole to charge screwdriver when case is closed Hold 1 extended shaft Multiple slots to add magnet…
I design this for my modular monitor attachment but I figure some people will find it useful. Pic is slightly different since design has change slightly to match with the table/wall mounting. The headphone holder can rotate to accommodate…
Zerofilter but for 2020 extrusions, all other file required from the original github page. “zerofilter 2020 Rear Brace”: b asically the same as the original brace but for 2020 extrusion “zerofilter 2020 Mid Brace side by side”: group the…
Require the universal hook from the original collection derived from https://www.thingiverse.com/thing:2853261 I included size: 5x3, 5x2, 4x3, 4x2, Request other size if needed. Display case is tilted at 12 degrees. Choose the either the…
Require the universal hook from the original collection derived from https://www.thingiverse.com/thing:2853261 Bits might be a bit loose/tight if printer are not calibrated, print it plus minus few percent. Holds 24 hex bits 20240825: add…
Require the universal hook from the original collection derived from https://www.thingiverse.com/thing:2853261 Fits set of 6, size from left to right, 6.8mm, 5.8mm, 5.2mm, 5.8mm, 6.8mm, use the 3 slots for the official skadis 2024.03.20…
To wszystkie aktualnie dostępne wyniki.
