Liczymy pasujące modele…
A ramp to lift one end of your Olympic Barbell with Weight off the ground to make it easy to change weight between deadlift sets. One version provided with holes for magnets and one without. Magnet link (ؼ" X ¼") =>…
Simple supports for your Test Tubes while attached to your formicarium available in 15mm and 20mm centerline height.
An adapter for the Magneto X to use the K1 version of Hula anti-vibration feet. Link to Hula files: → https://makerworld.com/en/models/417509#profileId-319901 Video link: →…
Remix of Mosquito Hotend mount for the Prusa Mini + from CrisPersi . Adds the use of the stock Bowden tube fitting and Super PINDA bracket. No change in Bowden tube length or nozzle position compared to stock. Uses a 13-13.2mm Teflon tube…
Added a draft to the of_portal_feederlid to aid alignment and keep the lids in place.
Gain 3.2mm more clearance for modified fan ducts with the 1.6mm tall ultra low profile heat bed cover. To gain this clearance the wires are relocated to the bottom side of the bed using special hardware, listed below. If you don't need…
IGN-1A Coil with corrected geometry based on measurements from the coils I purchased from DIY Autotune. https://diyautotune.com/products/ign1a-smart-ignition-coil?variant=42673491411053
Add dual 4010 fans to a stock Prusa Mini or SliceEngineering Copperhead. Uses Annex Engineering K3 4010 fan ducts, at original angles and spacing. Suggested 5V Fans: BFB0405HHA-A (2 wire, no Tach) or BFB0405HHA-AF00 (3 wire, w/ Tach) If…
Add dual 4010 fans to a Prusa Mini with a REVO hotend. Uses Annex Engineering K3 4010 fan ducts, at original angles and spacing. Suggested 5V Fans: BFB0405HHA-A (2 wire, no Tach) or BFB0405HHA-AF00 (3 wire, w/ Tach) If you want the fans…
Various parts that are useful for building an Air Trajectory Apparatus
TRAXXIS 7630 Suspension Arm revised to be easily printable on an FDM printer. Use your slicer to mirror as needed. Mirroring is only needed for visual preference. An Index drill set will be useful to cleanout the printed bores.
Fan ducts scaled up from the Annex K3 to fit the stock Magneto X Fans with a mount for a Beacon H probe. https://discord.com/channels/1158578009121501267/1246834133695594607
A mount to add an Annex Sherpa Micro Extruder (Mirrored Version) and a Slice Mosquito Hotend to a Prusa Mini. Mirrored Micro Parts Link=>…
Bigger ducts for the Magneto X. Prints well with the flow exit on the build sheet.
Remove one or both of your fans and install this CPAP fan duct that is rotated so the ducts face the front. Duct discharge nozzles and their placement are from Archetype Breakneck. For Medium and Long Meltzone Only (Does not accommodate…
A simple snug fitting plug to replace the tape covering the hole for the breaker switch that was relocated to the bottom left. side.https://discord.com/channels/1158578009121501267/1257134890135195710
Magneto X through Y Strain Relief for 1x 5mm Beacon Cable & 1x 4mm Bowden Tube. Hardware: 3x M3 x 5mm OD x 4mm Long Heatset Inserts 2x M3 x 12mm SHCS 1x M3 x 18mm SHCS Discord thread:…
To wszystkie aktualnie dostępne wyniki.
