Liczymy pasujące modele…
This Gridfinity battery dispenser fits 10 AA / 13 AAA batteries per 2x2x1 Gridfinity block, plus one dispensed battery. If you need to store more batteries, you can print another block that feeds batteries into the dispenser block…
2x2 version of Zack's nipper holder with the angle of the holders tweaked so they fit inside a 2x2 square. If you have long tools they will still stick out of the 2x2 area but not nearly as much as in the original (which works better in…
Introduction This is a functional print that helps you finally digitize those 35mm film negatives - old family photos and recently developed rolls alike. The main component consists of a frame with a print in place mechanism for advancing…
Maybe you're like me and don't have enough tools, and so printing the full sized version seemed like overkill. Here's a 2x2 version instead for holding only three nippers/clippers. If I need more I'll just print another. Recommend adding…
I've printed these with 0.20 mm layer height and a 0.4 mm nozzle. Breadboards are attached to the holder by sliding them in. Remove any adhesive pads from them first. The breadboard should stay in place fairly tightly, but if not you can…
Inspired by Zack's reconfigurable jumper holder and vanilla_chief's vertical jumper holder, here's one that combines both. Uses M3 screws and nuts to connect the pieces together. Print at least one base, two combs and two extenders.…
Printed on it's side, 3mf file should be oriented correctly. Needs supports, personally I used snug grid support under the green areas as follows: I recommend printing support interface layers using proper support material, or PETG if…
Idea from werz99 soldering jig. I simply made cuts into an empty Gridfinity bin. Print with small layer heights to make the cables stay in place better. After making this I noticed there's another version here, which might work quite a…
Link to the crappy multimeter I have: https://www.clasohlson.com/fi/Yleismittari-UNI-T-UT132E/p/Pr365256000 I've printed a 1x1x12 plain bin to hold the probes/cables in place. Use magnets + weighted baseplates to prevent these from…
Mount for a UniFi G3 Instant camera to a baby crib. You can route the USB cable through the holes in the model to hide the cable neatly. I recommend printing both models upside down, with supports on. I'm fairly certain that the clamps…
This is a spool holder for storing your cable, solder, etc. spools in as small space as possible. There are two wide slots at the front for unwinding the wire either from the top or bottom depending on your preference. The middle hole is…
I don't have all that many devices that need coin cell batteries, and as such I scaled down the original. Moments later I gathered all the coin cell batteries I have lying around and yeah, now the holder is full 😂
NOTE: The UCG-Fiber is a tight fit inside a 10 inch rack. Before printing, please make sure there's at least 216mm space between your rack rails, otherwise this bracket won't fit. I tried designing this so it doesn't use up too much…
This is a variation on the mflink part that rotates the link by 45 degrees instead of 0 or 90 degrees.
Original Gridfinity accessories and baseplates by Zack Freedman: https://thangs.com/designer/ZackFreedman NOTE: If you're going to add weights to the model, please make sure the dimensions of your weights fit in the slot. This model has a…
This is quite frankly not much more than a silly idea, but I just had to because my camera bag perfectly fits a 3x5 Gridfinity baseplate. More seriously, I've started to more frequently change which lenses I want to carry as of lately.…
Original Gridfinity accessories and baseplates by Zack Freedman: https://thangs.com/designer/ZackFreedman NOTE: If you're going to add weights to the model, please make sure the dimensions of your weights fit in the slot. This model has a…
Handy tool holders for common 3D printer cleanup tasks. Definitely make use of magnets and make sure your baseplates are secured to something sturdy, as some of these are quite top heavy. Attached source Fusion 360 file in case your…
Necessary hardware: Raspberry Pi Zero 2 W: https://www.amazon.de/-/en/gp/product/B09KLVX4RT/ USB hat: https://www.amazon.de/-/en/gp/product/B09B9Y17MV/ Optional heatsink: https://www.amazon.de/-/en/gp/product/B0B4JQQ8ND/ 1x M3x6 threaded…
This model can be used for mounting an Arzopa 144Hz portable monitor to a regular camera tripod with a ¼" screw. Required materials: Two M4x8 screws (non-countersunk) Two M4 nuts One UNC ¼" - 20 nut Assembly: Slot in the M4 nuts into the…
Here's a retro tree topper from a certain video game franchise that prints in under 3h and fits on Prusa Mini! ;)
NOTE: the front part needs to be flipped upside down before printing
Based on parametric 3D benchy: https://cad.onshape.com/documents/fdd43dab01647ffe24686ee9/w/ae15bd2f02e832b59a5766f7/e/73e17a2e24a1fc77118f59f8
This was a quick and cheap way of getting a baby monitor mounted to our stroller. The camera works over WiFi and can be powered via a power bank for quite a long time. The camera is easy to detach from the mount by simply sliding it out.…
We have this recycling box at home, and I got annoyed at the fact that you need to lift the lid aside with one hand (usually holding something you're about to throw into the box with the other!) and negotiate the lid in place every time…
Using this model you can mount a generic webcam to an IKEA OMAR shelf for e.g. monitoring your 3D print jobs. The webcam needs to have a standard tripod mount screw hole (M6) and the hole should be no further than ~20mm away from the edge…
To wszystkie aktualnie dostępne wyniki.
