Liczymy pasujące modele…
The whole dustbin has the following dimensions: Length: 86 mm Width: 66 mm Height: 94 mm The inner space has following dimensions: Length: 78 mm Width: 54 mm Height: 82 mm I designed wheels to put under the dustbin, but i did not glue…
This is a model I designed as a birthday gift. The upper arm is movable thanks to the two-part hydraulics. The V6 engine block hanging from the chain at the front comes from the following model: https://www.thingiverse.com/thing:40658 The…
I designed a replacement hook to open attic doors for example. The opening for the handle has a diameter of 23,5mm The hook works best with 75% infill. Its the best ratio between filament usage and stability i found through my test…
The box can be used as a support tray to work with weed or as a transport box to take it with you. Measurements of the closed tray: height: 4cm (each box-half has a height of 2cm) width: 12cm length: 21cm Measurements of the bulges: round…
This is a holder for the Anker Soundcore to put in the shower. You clip them on the glasscover of your shower as seen on the pictures. You have to print two of them (just multiply the print in your slicer). I put just one in the STL file…
A simple holding hook for a shower with a glass wall The thinkness of the glass wall i designed it for is 6,5mm ------------------------------------------------------------------------------------ Ein einfacher Abzieher-Halter für eine…
The ring has an inner diameter of 6mm. The plate on the bottom has a diameter of 15mm. For me the diameter matches perfectly the Busch Dimmer 2250 U. ------------------------------------------------------------------------------------ Der…
I have designed a very simple straw holder because my straws were no longer getting clean in the dishwasher. The holder has outer dimensions of 65 mm × 45 mm with a height of 35mm (higher end of the slope) and provides space for 12 straws…
This is a plate which can be used to sort out screws while repairing a electrical device (e.g. a Notebook) so you can remember, where to put each screw. If you want you can freeze some water in it to get some very tiny icecubes... The…
The ball stand has the following dimensions Width: 70mm (inner distance) Length: 70mm (inner distance) Height: 10mm (outer stands) The Playmobil figure is for scale of the ballstand. It is a big tennis ball ;)…
This is a "Coaster Box" to fit 100mm (10cm) drink coasters. About 6 coasters fit in the box. ------------------------------------------------------------------------------------ Dieser Halter/Ständer kann für das Lagern von 10cm…
The Thing is a replacement thread insert for the Grohe 47453IPO shower shut-off handle because the original replacement part is very expensive. After the print you need to clean the threads from the support material with some tweezers.…
I designed a spool holder for the biggest drawer in my Hemnes dresser. My drawer got the following measurements: width 84,3cm, depth: 43cm and height 24cm. The spools fit perfect while you can easy open and close it. Additionally you…
The french cleat, for which I designed the holder, has the following dimensions: Front height: 6cm Back height: 4.5cm Wedge angle: 45 degrees General print info: I chose 15% gyroid infill. It is very important to pay attention to the…
The air plug has following dimensions: Diameter (cylinder): 6mm Diameter (upper part): 11mm Total height: 21mm ------------------------------------------------------------------------------------ Der Ventilstopfen hat folgende…
With this model, I wanted to recreate the well-known "Red Panic Button" for a smart home scenario, since I could not find a finished button in this form online. I tried to document the process as thoroughly as possible with the pictures.…
The bolt spacer has following dimensions: Diameter: 20mm Height (curvature point): 20mm Height (outer part): 27mm Screw hole diameter: 7mm I used it to replace a missing part in the baby stroller of a friend.…
The box has the following outer dimensions: Width: 120mm Length: 100mm The hooks in the back have an opening of 4mm. The Box has the german word for sugar imprinted on its front.…
The USB holder has following dimensions: Height: 18.5 cm (185mm) Width: 35 mm For the 4 magnets on the back of the holder use 8mm*3mm ones (Holes are 8.5mm*3.1mm for a smoother fit) It can hold up to 4 big usb-sticks or 4 to 12 small…
The holder has following dimensions: vertical: Height: 23mm Width: 19 mm horizontal: Height: 19mm Width: 30mm The width is optimal for Tesa Mounting Tape (in both orientations)…
To wszystkie aktualnie dostępne wyniki.
