P
PrintablesDivideby0
Wall mount for DeWalt DCS356 Oscillating Tool
Wallmount for DeWalt DCS356 Oscillating tool
- Pobrania
- 792
- Polubienia
- 129
- Ocena
- 5
Wszystkie modele
Liczymy pasujące modele…
P
PrintablesDivideby0
Camelbak Drying Stand
Drying stand for Camelbak and other hydration reservoirs - base is a water bottle/mug/cup drying stand by itself. Works for 2L and 3L bladders
- Pobrania
- 786
- Polubienia
- 126
- Ocena
- 4,77
P
PrintablesDivideby0
Center console drawer for 5th-Gen 4Runner
Printable drawer for bottom cubby in 5th-Gen 4Runner center console. Supports recommended for the pull handle only Recommend adhesive-backed felt on the bottom and rear corners for best fit. RAM ball variant available here:…
- Pobrania
- 687
- Polubienia
- 58
- Ocena
- 5
P
PrintablesDivideby0
Wall mount for DeWalt DCS334 Jigsaw
Wallmount designed for DeWalt DCS334 Jigsaw v2 - updated to improve fit with protective plastic cover on base
- Pobrania
- 597
- Polubienia
- 87
- Ocena
- 4,33
P
PrintablesDivideby0
Wall mount for DeWalt DCG412 Angle Grinder
Wall mount for DeWalt DCG412 Angle Grinder
- Pobrania
- 546
- Polubienia
- 56
- Ocena
- 5
P
PrintablesDivideby0
Wall mount for DeWalt DCW210 20v random orbit sander
Wall mount for DeWalt DCW210 20v random orbit sander
- Pobrania
- 465
- Polubienia
- 60
- Ocena
- 5
P
PrintablesDivideby0
Altoids insert to hold LTT Screwdriver bits
Altoids insert to hold LTT Screwdriver bit sets - holds 4 sets (48 bits) Note: to avoid rattling, the insert will need small shims on either long side (it has to be smaller than the opening to fit past the rolled edge); I used the end…
- Pobrania
- 319
- Polubienia
- 64
- Ocena
- 4,67
P
PrintablesDivideby0
CPAP hose drying hook
Drying adapter I designed for the Resmed CPAP hose - fits shower fittings 20mm or less in diameter
- Pobrania
- 290
- Polubienia
- 52
- Ocena
- 5
P
PrintablesDivideby0
Tripod Wall bracket
I wanted a better storage solution for my tripods and other support gear than piling them in a closet, so I designed these wall mounts to hang them from the ball head. Large: 25mm throat, 75mm clearance under the plate Standard: 20mm…
- Pobrania
- 214
- Polubienia
- 40
- Ocena
- 5
P
PrintablesDivideby0
Steamdeck dock snap together version
A snap-together version of the Steamdeck dock. This variant is currently untested Changelog -v2 released: revised geometry based on user feedback for easier assembly
- Pobrania
- 134
- Polubienia
- 12
- Ocena
- 4,33
P
PrintablesDivideby0
Tool mount for Mellif cordless hot glue gun
Mount for Mellif cordless hot glue gun
- Pobrania
- 96
- Polubienia
- 23
- Ocena
- 5
P
PrintablesDivideby0
RAM mount for 5th-Gen 4Runner
It uses M6 hardware for the front plate and fits RAM ball RAP-B-354U-TRA1. I used Cat tongue tape on the bottom, center, and corners to keep it from sliding out,
- Pobrania
- 69
- Polubienia
- 10
- Ocena
- 5
P
PrintablesDivideby0
Wall mount for DeWalt DW3742C Jigsaw blades
Wall mount for DeWalt DW3742C Jigsaw blades
- Pobrania
- 60
- Polubienia
- 9
- Ocena
- 0
P
PrintablesDivideby0
Divider for 3rd-gen Toyota Sienna Cupholder
Lost the original part years ago, so I designed this to replace it. Recommend placing felt on either side for a tight fit without any rattling while driving. Note: print upside down to avoid needing supports
- Pobrania
- 60
- Polubienia
- 6
- Ocena
- 5
P
PrintablesDivideby0
RAM Mount adapter for Yaesu FTM-500DR remote head
RAM adapter for Yaesu FTM-500DR remote head. It matches the RAM-B-347U base. Uses all M5 hardware with Nyloc nuts. Support is only needed for the center M5 bolt that attaches to the back of the remote head. V2 model available in 2…
- Pobrania
- 59
- Polubienia
- 11
- Ocena
- 5
P
PrintablesDivideby0
Low Beam cap wrench for 5th-gen 4Runner (2010+)
Wrench to remove the weather cap when replacing the low beam bulbs on a 5th-gen 4Runner. The orange model in the photos was the prototype - red is the final design. Holes are for a screwdriver shaft to gain extra leverage if needed
- Pobrania
- 51
- Polubienia
- 10
- Ocena
- 0
P
PrintablesDivideby0
Mount for DeWalt DCF510
Printable mount designed to hold the DeWalt DCF510 20v Brushless ratchet when paired with the 2AH battery
- Pobrania
- 33
- Polubienia
- 7
- Ocena
- 0
P
PrintablesDivideby0
Amateur HT antenna quiver mag mount
Magnetic antenna quiver for HT antennas. The magnets may be found here: https://www.amazon.com/dp/B07DGTT52D?ref=ppx_pop_mob_ap_share
- Pobrania
- 28
- Polubienia
- 3
- Ocena
- 0
P
PrintablesDivideby0
Lens cap for Logitech Streamcam
Needed a lens cap to protect the lens while not in use. Friction fit with recessed center cutout to prevent scratching the lens
- Pobrania
- 17
- Polubienia
- 0
- Ocena
- 0
P
PrintablesDivideby0
Hairdryer Mount & cable keeper
Hairdryer mount and cable keeper Uses M6 locknuts and M6 bolts (2 pairs each for mount and cable keeper)
- Pobrania
- 11
- Polubienia
- 1
- Ocena
- 0
To wszystkie aktualnie dostępne wyniki.