Liczymy pasujące modele…
Want tape holders that are easier to print and stay put? These use the t-bolt multiboard screws as a base and extend them out 75mm or 100mm to hold rolls of tape. They're nicely secure and don 't droop.
The hammer hooks I found weren't all that secure, so I just put one together using the push-fits as a basis for the model. There are 2 variations here: 3 connectors and offset 2-connector variants. The gap between the pegs is 36.5 mm
These allow you to mount your crossbars on the wall however you'd like. I wanted separate brackets so I could have towel racks when the bars aren't installed on the truck.
I wasn't a fan of all the supports required from the original model, so I remixed it to improve rigidity, remove supports, and angle the fighter downward. STLs have been exported in the optimum print orientation
The voron subreddit gives you a pre generated serial plate but it does not fit the v0.2 skirts. I modified the v0 STLs to fit the v0.2. To make your own, you're going to need OpenSCAD. Just download the files, open the scad file and…
This was tested with Crossbars purchased in 2023 using ABS filament. I do not recommend using PLA as temperatures inside the bed can get high enough to melt and deform PLA. BOM: 2 x 30mm M6 Bolts 2 x M6 Washers Mounting Instructions:…
For those who want a caliper mount that screws in more securly than a snap mount.
I have an old set of Tekton precision screwdrivers that needed a home. This is a 2x5x4u stackable unit
Hang your pTouch labeler on your multiboard using multipoint mounts.
Screwdriver and bits holder for Zack Freedman's Gridfinity organization system. Holds: Sequre ES126 Electric Screwdriver iFixit Screwdriver Standard 4mm bits that work with both
Remix of the Switchwire X-Carriage so you can mount a Revo Voron PZ Probe board on the carraige with M2 screws.
This is a remix of the P-touch H110 wall mount holder to work with 1-inch pegboard.
Add some color and flair with a custom backing/surround accent plate for your stern pinball machine. I tested this with my Jurassic Park Premium machine. I assume it will fit most modern Stern machines. The ones you can buy are acrylic…
This is a case for the Spirograph . All parts fit in 3 layers: Bottom: 155, 63, 40, and 36 Middle: 144 and 80 Top: Everything else
This remix makes adjustments so they can be printed face down without support. Recesses around the holes have been adjusted so a slicer printing at 0.2mm layer height or finer shouldn't try to print in mid-air.
If you want super consistent spacing and mounting of hoiday lights on your crossbars, this will do it for you. There are 3 main components: 4-piece Rail Insert: Each channel in each side of each crossbar gets 2 of these. They hold 4…
If you have a lot of M3 hardware sitting around and want to put some Kicker CSC5 speakers in your Stern pinball machine, then these plates will work for you (assuming you don't want LEDs). See the original for installation instructions.
22mm Modulator Atomizer Holders can be linked together. This is a dual extrusion print where the 22mm center is separate from the block. Instructions To dual print, use the dual inside and dual outside STL files. For convenience, you can…
I wanted to put some gridfinity battery holders around my charger, so of course I needed a gridfinity base to hold the charger!. Example printed in PETG
Pegboard isn't great for 3d printing so I've switched to multiboard and wanted to hang up my multimeter. This remix keeps the mount in the multimeter and you can simply slide it on and off your multiboard using a multipoint screw.
Modular platform that fits an XTAR VP2 Charger, 2 18650 batteries, and a 26650 battery. Updates: Fixed the interlocking tabs/slots to properly fit together. Category: DIY
A frame you can glue or epoxy into your mod to hold your SX350 chip/ Instructions Test prints used ABS at an extruder temp of 220C on a heated platform at 110C. Be sure to set shells to zero or you'll end up with hollow walls. Category: DIY
To wszystkie aktualnie dostępne wyniki.
