Liczymy pasujące modele…
Purge Cover needs to printed in a flexible filament (TPU or TPE) and works best with the original retaining ring from the regulator. If the original retaining ring is toast, there are 3 versions of the retaining ring (they should be…
Scuba BCD Bladder Flange modeled off of DGX Flanges. In the pictures the red is ABS printed from my design, the black one is a DGX commercial product. I made mine parts interchangeable with the industry standard. the last picture is…
Roller cams for the HTLF mmu. Uses MR63ZZ bearings (2 per cam, 8 total): https://www.amazon.com/dp/B075CMRGY6?ref=ppx_yo2ov_dt_b_fed_asin_title&th=1 M3 SHCS (3 10mm, 1 12mm) One BT Cereal print is the extent of testing at this time. Use…
Pictures are version one in which the belt geometry is off (you can see the belt pulled in). attached files run the slider full height, and the face of it 5mm closer to the rod (should have the belt straight/much closer to straight).…
JST 4 way splitter for 2020 suitable for fans, lights, or power. Press in the JST sockets, then solder your innput wire as a buss bar. I recommend potting it with hot glue after solder is done and checked for continuity. I designed it to…
Harness Hardware for use with 1.75 inch webbing Category: Sport & Outdoors
Use at own risk. Category: Sport & Outdoors
Provides more support to the motor shaft, hopefully prolonging the life of it. Uses F695-2RS bearing (already on the BOM for the Simplecore). Edited to add mirrored copy
Scuba Inflator Elbow, works with DGX Bladder Flanges. I printed mine in PLA, and it leaks slowly (over the course of hours). Disclaimer: for educational use only, has not been tested in water, use at own risk, etc. Print Settings Printer:…
Tool for outer portion SCUBA BCD Bladder Flange. Works in concert with https://www.thingiverse.com/thing:2534711 created by Homer310. Print Settings Printer: GEEETECH MeCreator2 Rafts: No Supports: No Resolution: .2 Infill: 50% How I…
Simple umbilical guide mounts to the extrusion frame. the 2 ziptie slots break out easily depending on print orientation, but are not crucial.
Designed for someone on the discord, I haven't printed it. They, however, said it fit properly first try.
Press on T's require very soft TPU (the common shore 95 stuff will be to firm to get on/off). Very limited testing. Screw on T's do fine in any TPU. Print Settings Rafts: Doesn't Matter Filament Material: TPU Category: Sport & Outdoors
TPU buttpad for AR-15 / M4 Milspec stocks. Made for my son's Airsoft M4 I use an IDEX printer and use PLA for supports (pop right out) Print Settings Supports: Yes Resolution: as desired Infill: As needed for desired firmness Filament:…
Been a while since I printed these.... 4 versions (varying thickinesses of material). Purge cover itself prints in TPU, diaphragm retainer and face ring print in ABS or PETG Category: Sport & Outdoors
Rendering of diaphragm cover, modeled in Freecad. will be attempting to print in TPU, but I have concerns about supports... will update as it progresses. Edit#1 Support worked out surprisingly well. Thickness of outer ring was too much to…
2 versions of dust caps for regulator 1st stages. I make no promises of being water tight, use at own risk, etc. I printed in TPU and do not use an o-ring on them. Category: Sport & Outdoors
Back is done in PLA, front is done in TPU Category: Sport & Outdoors
Cap for Scuba second stage inlet fitting. Used https://www.thingiverse.com/thing:2306170 by DiverMike as a hole generator to make. Print Settings Printer: GEEETECH MeCreator2 Rafts: No Supports: No Resolution: .2 How I Designed This…
As named. Use at own risk. No guarantee of proper fitment. Don't fry bacon naked. Category: Sport & Outdoors
Pin spanner takes 1.6 mm steel rod pieces pressed in with a vice for the pins. Adjustment tool uses sheet steel cut to size and pressed in for the 2 "blades". Replacement Cap and Spring cap are untested. Category: Sport & Outdoors
BCD dump valve, two versions (fancy and plain). The Plunger piece requires the actual rubber seal to be glued to it. In addition to the rubber seal you will also need the spring, and pull cord (cave line or similar). Version 3 is for the…
Seat saver key for the SP 108/109/156. Designed in 2 parts for ease of printing. Insert the key through the center of the "S" disc on the regulator and turn 90 degrees to lock in place. keeps the lever depressed without deforming the…
Printed replacement for factory tool. Category: Sport & Outdoors
Replacement saddle for ScubaPro Mk10 Category: Sport & Outdoors
Replacement for the chrome "S" disc on vintage Scubapro Regs Category: Sport & Outdoors
1st stage to body, and body to can gaskets are only a stopgap for when rubber and nylon ones are unavailable. Print in TPU, and the 1st stage gasket is very sensitive to over-torque. Mouthpiece plug is for the USD curved mouthpiece. Older…
Replacement purge button for ScubaPro G250 Category: Sport & Outdoors
Print 2 outer mold halves and 1 inner mold. secure together with screws and wrap seams with electrical tape. Fill via flare holes with 2 part mold making silicone, holding mold at an angle filling from lower hole until silicone flows out…
Replacement faceplate for ScubaPro 108/109 Category: Sport & Outdoors
Replacement for Aqualung (and probable other) Double Hose can clips. Uses m3 screws. Category: Sport & Outdoors
Small holes are for 3mm screws to secure the mold, flared holes are for injecting silicone (hold at angle and fill from "lower" hole until silicone comes out upper hole free of air bubbles). Use 2 part mold making silicone. Seal seam…
This is a screw for mounting a lens cap holder to the bottom of a DSLR camera. I trimmed an existing model to fit within the recess on the holder I printed (thing 345087) Print Settings Printer: GEEETECH MeCreator2 Rafts: No Supports: No…
To wszystkie aktualnie dostępne wyniki.
