Liczymy pasujące modele…
More versions available at the original creators link here: https://www.printables.com/model/1318288-elegoo-centauri-carbon-side-panel-protector-spool
Prints without supports. I ordered the following acrylic panels for mine, the model can accept up to 4mm deep panels, but I went with 3mm as it was more readily available: Dark tinted 3mm panels from cutmy.co.uk for approx £25 delivered -…
Another Shaun of the dead nametag, created from scratch in Tinkercad as I couldnt get the other one to print well enough. The original version has text that is proud of the backing by 0.3mm to allow a couple of layers of white on top for…
Hopper bung / side breech cover for the Valken CQMF, may also fit the M5 from Milsig, but I dont have one to check. Category: Sport & Outdoors
A5 Freak insert barrel for Tipx, M17 etc. Print threads at highest resolution possible. 0.07mm worked fine for me, 0.1 should be ok Category: Sport & Outdoors
Project box intended for customisation. I've included a joystick / button box lid which I created this for as an example. Add your own cutouts / slot for usb cable or whatever interface. Added additional box bottom with a cutout for an…
Ball detent for Valken and Milsig M17 M5 and CQMF markers Print in flexible TPU, simples. Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: No Resolution: 0.2mm Infill: 100% Filament: Any - its all the same TPU…
Lightly remixed version of Walter's excellent deflation valve adapter with a longer thread for deeper valves Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: No Resolution: 0.2mm Infill: 20% Filament: Any -…
This is a support for fitting smaller downlights in a pre-existing hole, the insert is added to the upper side of the hole and is glued or taped in place, it allows plaster to be added in the gap between the existing ceiling and the part…
Top pic rail for the Milsig M17 marker. I originally put holes in for the retention pins but ended up drilling these after instead as it was difficult to get good alignment, also the holes on my receiver were on their last legs so I glued…
Breech cover for the M17, pretty much a direct copy of the original, as best as I can in Tinkercad in any case. Should print without supports at 0.15mm or less layer height. Print Settings Printer Brand: Creality Printer: Ender 3 Rafts:…
Dummy surpressor for 22mm OD paintball barrells with metric threading on the end, comes out nice with fuzzy skin - 2 lengths
Simple spring tensioner for the X55 and X65 HOTAS from Saitek and more recently Thrustmaster, just slots under the spring if you've lost the original spares that came with the stick like me! Print Settings Printer Brand: Creality Printer:…
Small case for EDTracker DIY build (does not house the official PCB), I used a 6 pin JST connector inside to join the MPU and Pro Micro, connected via the following: (Pro Micro left, MPU Right) VCC > VCC GND > GND P3 > SCL P2 > SDA GND >…
This is a barrel nut replacement, not to connect a handguard, but to replace the threaded hex nut connectors where they have been lost, this joins two 10mm M5 button head nuts in the middle - i.e. the connectors that go through the marker…
Collar that surrounds the squarehead for Milsig and Valken magazines, print in fine resolution ideally as the lip that positions the squarehead properly needs as much integrity as possible. Print Settings Printer Brand: Creality Printer:…
This is a homage to the superbly designed T15 5 round mag from Donutmaster34 - check out his original here: https://www.thingiverse.com/thing:2466296 where he has an excellent video. Please see his other versions which achieve some of the…
Simple adapter to allow smaller 8g Co2 to be inserted, requires a 5p piece to be glued in the bottom so that it doesn't get chewed up.
Air through adapter to allow a hpa hose to be connected to your marker / rif through the rear when using a SARB-15 bullpup ar15 kit. Designed to print in firm plastics like pla, petg etc. if printed in rubber you'll need to adjust the…
I wasn't happy with the deauther cases available so wanted something that would print easily without supports, hence this, not the prettiest but functional. Has a hole in one end to fit a switch so a little soldering is needed, also large…
Battery goggles strap holder for emachine 1600ma 7.2v usb battey Print Settings Supports: Yes Resolution: 0.2mm Infill: 50% Category: Hobby
This is a 28mm drain tap bracket for motorhomes / caravans, it replaces the brackets that come with these: https://caratechcaravanparts.com/products/caravan-motorhome-28-mm-fresh-water-drain-tap-with-fixing-bracket-w4-00007 with a much…
To wszystkie aktualnie dostępne wyniki.
