Liczymy pasujące modele…
For when the standard crevice tool just isn't narrow enough :) Made for 35mm fitting. You might have to lower the power of the vacuum cleaner as the narrow point restricts airflow a lot.
An organizer that clips around the edge of the bucket. You can store 5 brushes in the premade holes and extra, bigger items in the big compartiment. In the bottom there are some holes to get rid of the water.
An adapter to make a tong from any desired utensil (spoon/fork/…) Print needs supports. Scale as needed for your utensils. You might want to use other filaments to suit your use case (heat-resistant/foodsafe/…)
Scale to desired measurements in slicer. Tip: Emboss text with contents for easy recognition of medication.
Print 1 per tyre. Drive the car onto the tyre-up. Make sure the tyre is hanging over the edge with the sidewall. You can clean/dress the tyre without the bottom touching the ground leaving an untreated spot. As an extra there's also a…
We were tired of our hangers always getting tangled in a basket so I made this wall-mounted clothes hanger storage which perfectly fits behind the door of our dressing room. Easy, fast and cheap print. Supports needed.
Based on the item below I started drawing from scratch in an attempt to enhance it. So I guess it isn't really a remix? https://www.printables.com/model/330308-desk-aaaaa-battery-dispenser-discharged-battery-co/comments Changes: Added…
A simple breakaway clasp. Print without supports, both with the small diameter down for similar prints on both parts.
A collection of Rudolph the reindeer ornaments: Basic version (just as a painting project for kids or to be remixed) Christmas tree ornament Napkin ring
One of our cats always scoops out the litter out of the robot. Therefore I made a guard to prevent most of the litter from exiting. As it's kind of complicated to make the fit still isn't 100% but as of this version it stays in place when…
My son lost one of the bunnies so I scanned and recreated it.
I made cable management clips to fix cables in place inside of the aluminium profile. Depending on the used materials, you might have to scale a bit to get a perfect and tight fit. Feel free to buy me a coffee :)…
Not much to say about it :) Just a martial arts belt. Scale as you like, pick a color and print! Make sure you use supports!
As you don't really want to let chemicals flow through your pressure washer, the mounting spot for the Plug&Clean module is kind of useless. On the other hand it's a perfect spot to put your foam lance. Therefore I made an adapter piece…
I wanted to be able to hang my quick release nozzles on the wall so they have a fixed spot. For this version I made a wall bracket for the complete set. There are holes in the bottom of the fittings for a 4mm screw. The margins are very…
Just a funny Thanksgiving turkey. Possible uses: magnet, decoration, let the kids paint it so they'll be quiet for 10min :D The Towel Holder: https://www.printables.com/model/1482744-thanksgiving-turkey-towel-holder The Napkin Ring:…
Will print easily without supports. I printed it at 0.12mm for a smooth result but I guess 0.16mm will do the trick as well. In the second file I tried to print an inlay for the center line. As it is so small it's very hard to create a…
Just an easy tool to remove the crown from your strawberries. Prints in less than 20min with less than 3m of filament. A bit of support is needed.
After falling numerous times the original was unfixable so I made a new one. Print with normal supports at 25° treshold angle to support the overhanging portion of the part.
A simple plug designed to close off a PVC drain pipe with a 35 mm inner diameter and 40 mm outer diameter . The plug is designed to provide a water- and odour-resistant seal for an unused drain pipe. For an improved seal, especially…
I wanted to be able to hang my quick release nozzles on my pressure washer's handle for quick access during cleaning. For this version I made an attachable storage for the complete set. The ring is made out of 2 parts which slide into one…
Just a tulip vase, but a bit different :) You can store some flowers in the middle and 1 in each of the holes on the side.
Level up your thanksgiving table decoration with this napkin ring :) The Turkey: https://www.printables.com/model/1482731-funny-thanksgiving-turkey The Napkin Ring: https://www.printables.com/model/1482738-thanksgiving-turkey-napkin-ring
I wanted to be able to hang my quick release nozzles on the wall so they have a fixed spot. Theres a hole in the bottom to fit a 4mm screw. The margins are very tight for the locking part and as some quick release nozzles have slightly…
As i needed to cover up the 3 ventilation holes for my pellets stove I made a grille that overlaps all of them. The vents are angled down 45° so the air will be directed to the floor instead of straight trough. 3MF-details: This item is…
A simple keychain featuring the iconic Fiat barchetta logo, perfect for owners and enthusiasts of this classic Italian roadster. Print it as: Single-color version – simple and quick to print. Multicolor version – features the logo in…
I guess a phone mount could be handy to attach to the front of the case. Due to the angle and possible weight of the phone I guess PETG will be the way to go.
This seat belt guide is designed to help the seat belt retract neatly instead of remaining loose or hanging when not in use. The design is based on a drawing originally shared by a user on the Dutch Fiat barchetta forum. The original…
In case you'd need some more dividers. Ideal for organizing smaller items and/or less used ones. Slicer makes very minimal support so it doesn't seem necessary.
A tree replacement for a Goki wooden toy set. For extra strength, print the tree base cilinder on a 45° angle with supports.
To wszystkie aktualnie dostępne wyniki.
