Liczymy pasujące modele…
Pretty standard dimensions for 2.2 inch RC wheels. The 2wd fronts use 8mm x 3mm ball bearings. The rears and the 4wd fronts use the standard 12mm hex. I suggest PETG for strength, but it might work fine with PLA, I just haven't tried…
I didn't have much M4 threaded rod on hand, or knurled thumb screws, so I reworked a design to use cheaper and more common hardware. For this project, you'll need M4x25mm screws (14) M4 hex nuts (14 or 25 if you're also printing the thumb…
I created this to hold the controller board for my scale truck light system. Print instructions Category: R/C Vehicles Print Settings Printer Brand: Prusa Printer: i3 MK2.5 Rafts: No Supports: No Resolution: .2mm Infill: 50%
Pretty standard dimensions for 2.2 inch RC wheels. The 2wd fronts use 8mm x 3mm ball bearings. The rears and the 4wd fronts use the standard 12mm hex. I suggest PETG for strength, but it might work fine with PLA, I just haven't tried…
Pretty standard dimensions for 2.2 inch RC wheels. The 2wd fronts use 8mm x 3mm ball bearings. The rears and the 4wd fronts use the standard 12mm hex. I suggest PETG for strength, but it might work fine with PLA, I just haven't tried…
I recommend printing this in something that is UV and weather resistant. Most 1quart mason jars should fit. I use a sharp piece of 1/6 inch piano wire to punch holes in the lid. Print instructions Print Settings Printer Brand: Prusa…
I created this to attach to some raised beds to keep pests out. It's a modular system, and could be used without mounting to anything - just build the frames, and place them on the ground. It is modular and extensible It is lightweight It…
When the Ultima was re-released, I had to have one. My first competition buggy was a Turbo Ultima, and I bought it right after Jay Halsey won the championship with it. And then I waited for a Turbo Ultima re-release. And that hasn't come…
I made these for use with the Featherboard with Tilt by FellowWoodwork because I have an older Bosch table saw that doesn't have the T-slots. The action of tightening a nut on the bolt pulls the bolt up, spreading the ears. These should…
I store my filament in dry boxes on a shelf above my printers. When I got my XL, I found that the filament sensors were in a place that didn't work with that layout very well. I moved them to the top, and then I found that the PTFE tubes…
This is used to keep bees from drowning in the honey during harvest. Cut a hole in the harvest bucket a little bigger than the hoses, but smaller than the manifold. Use 3mm screws and nuts to hold it together. Print instructions Print…
Combination of two designs. I printed these with supports, but you could probably get away without them.
After making a remixed Inkle Loom , I made this pick-up stick. This little tool will make using your Inkle Loom a bit less tedious. Use the fine tip to pick your threads. In order to get the smoothest possible finish, which will help…
Clips on to the top crossbar of your Prusa printer. Designed for this rechargeable LED light bar: https://www.amazon.ca/gp/product/B06XQ39PMF For taller prints, it can clip on the back of the printer cross bar in order to be out of the…
4" and 6" circle looms for weaving plain weave and colour-and-weave designs
Like the other rims I designed, these have some built in support for the tire ribs, and work on cars with 12mm hex hubs. After they print, just peel off the built in supports. These work well with multi-color prints, I think. These will…
I have an older pre-lit artificial Christmas tree, made by Santa's Best Craft. The lights are a GE ConstantOn string. The light string uses a weird bulb - it's a 6mm bulb with a weird pinched base. I can't find the proper bulbs anywhere,…
To wszystkie aktualnie dostępne wyniki.
