Liczymy pasujące modele…
This mag loader was made because no one had made a simple mag loader which both stopped the mag from sliding out the bottom and stopped you from loading 31 rounds into a pmag. The plunger should fit in perfectly with no extra room when…
Very simple 38 / 357 speed loader that actually keeps the bullets aligned, actually has a detent, and actually fits without getting jammed at an angle. - Uses a single M4 screw between 10 & 30mm long. - 20-30g of filament depending on…
This is my 7.62x39 version of my 5.56 AK magazine loader which is an AK version of my 5.56 AR-15 magazine loader. I used both bulgarian polymer mags and steel mags for sizing. This should fit 30 rounds and the plunger with no extra room,…
20 and 25 round magazine loader for AR-10 / LR-308 magazines. Specifically magpul pmags. You can tell they're loaded completely because the plunger should snugly fit inside. The plunger will not fit inside with extra rounds in the tray.…
Simple glock mag tool. Print at 100% with basically anything other than TPU. I used PETG and it worked fine. The AC Unity tool uses a M3 socket head bolt, any length. The OEM / KCI tool uses M2.5 socket head bolts, any length. You can…
Print with like 6 walls and however much infill you want. Use 95A TPU for the holster and anything else for the ram-rod. It gets a little stiffer & rougher if you print at like 270C. ------------------------- This holster attaches to…
This paper cartridge former is specifically for 50 caliber muzzle loaders with 60/70 grain powder charges utilized round balls or minie balls. You must use coffee filters or other similarly thin paper such as cigarette paper. If your are…
These AK adapters are made for AKM (with or without tang) to a mil-spec AR buffer tube or 1913 picatinny rail. Materials ----------------- Reinforced versions take three to four M4x20 button head bolts to prevent layer separation for…
This is an AK version of my 5.56 AR-15 magazine loader. I used WBP magazines as a sizing guide. The plunger should fit in perfectly with no extra room when exactly 30 rounds are in the loader.
50 caliber ball starter for muzzle loaders. Comes in short and long variant. Wide flat base for easier loading compared to round or T base designs. I recommend printing in 95A/72D TPU or PETG with the fan off. Other materials with good…
Mag Loader for 45 caliber single stack 1911s and 7.62x25 Tokarevs. PRINT UPSIDE DOWN -------------------------------- If you're silly you can use it for stuff like makarov magazines, but its a little janky for shorter calibers like that.…
Not sure why all the G3 handguard models out there are made for display, but here's an actually robust model. At 100% infill in ABS this is about 130g. Feel free to edit it to fit your needs. If you want this to be exceptionally good then…
Print with 95A TPU, takes eight 1x10mm magnets. You can download the no-magnet version to edit the model for your own magnets. Print Settings: Add as many bottom layers as you need to have a solid back, then add however many walls &…
No additional hardware is needed, you can thread screws directly into the print. ------------------------- These are mil-spec sized buffer tube adapters. There are 4 variants; Iron-height / in-line recoil with sturdy & lightweight…
Print at 100% infill. I did mine out of ABS but PLA+ or nylon would probably be best. You will need: -Four M4x20mm bolts -Some type of cordage / string. Assembly: >Screw sides to the handles with M4x20 bolts. Screw from handle to the…
Just a desiccant box I made because I was frustrated with other boxes. I sized it to fit between rollers in a large dry box. The lid doesn't fit quite right until both the box and lid are the same temperature so if you try and put a hot…
Large and small dispenser for 3D printed #10 percussion caps: https://www.printables.com/model/960060-new-and-improved-10-percussion-caps Requires super glue and a pens spring or other similarly sized coil spring. I used a .4x5x25mm…
If you have an existing model and want to add an mlok cutout or a picatinny rail / 1913 rail / nato rail to it, these assets can be used to do so. I'm sure if I dug for long enough I could find someone else who made these without random…
>Round and Oval handguards for internal piston and external piston uppers. >These are 2 piece drop-in for round carbine length end-caps and are sized for 10.5" barrels. > Accessory pack includes m-lok cutouts, 1913 rail segment, a…
This is for installing drop-in handguards. Screw the pieces together with M4x20mm screws, put the hook in the magwell, and lever the tool to install the top-half of the handguard first. Then put the ring over the end of the tool, slide it…
This is just a remix of the vent tab on LEOTE's lid with vents for the K1 / K1 SE. I guess the original version was made so you could put a dry box on top of the printer… but you can't use the vent in that case so why not add a large…
A wrench for the law folder. If it breaks, there are holes to thread in M4 bolts to reinforce it. You can put a screwdriver through the horizontal hole to spin it, or use a 12mm wrench. Print at 100% infill. Its only 10g, best to print…
Buffer tube adapters for RIA All-Generations pattern receivers. High grip allows you to get a higher grip so the trigger pull is normal, but it can be awkward depending on your hands. The low grip makes the trigger have a heavier pull but…
Just a simple webcam cover that's print in place. Glue the small end to the top of your webcam.
To wszystkie aktualnie dostępne wyniki.
