Liczymy pasujące modele…
Wall mount hose holder for garden hose. Prints on the side and should not require supports. NOTE : Four versions: One with angled screwholes so the front part won't be in the way when screwing into the wall. One with straight holes that…
Adjusts angle of the built-in camera so it points down more (centered a bit below the nozzle). I recommend using Arachne wall generator to handle the very thin loop. Category: 3D Printer Parts
Prints without supports, but supports could be useful anyway.
Pretty useless but fun project ;-) Fits a ESP32-S3-Zero / RP2040-Zero and a 0.96" OLED. The MCU is fastened with hot glue, the bezel and foot using CA glue or similar. The new version also fits a piezo buzzer soldered to the MCU. UPDATE…
Most Thermacell adapters are fragile because of the middle pin being so very thin. This version solves this problem by using a small piece of filament inserted into the middle hole. Fasten with e.g. CA glue. The tolerances are very…
NOTE: The pin on my BIQU Microprobe unscrewed itself after several prints - probably due to vibration. The pin can be unscrewed (see photo) and some loctite applied to the threads before screwing it back in. I've tested this a while now…
Prints flat without supports - Optimized for bridging. Almost post-processing free.
Holes are 40 mm deep, 12 mm diameter.
Printed fine with the face with one large opening down on the bed.
Small-ish headphone holder that screws into the edge of e.g. a wood bench. Sticks out 40 mm and is curved like most over-ear headphones. Printable without supports in the STL orientation. Test-printed in PETG using 15% grid infill.
A small color palette I use when painting 3d-prints. The example STL file has 2x3 25mm wells and 10 and 7 mm brush holders. Made in OpenSCAD - rows/columns and all diameters are configurable.
After printing, trim off the flat part of the rod end before pressing into the mixing head. Superglue the connection.
Needed a small but sturdy scoop / garden shovel thing. Printed in nylon, but will probably work with any of the more robust filament types. Prints fine without supports. Test-printed using 0.4mm layer height, and 0.6 mm nozzle. Category:…
A sturdy triangle shaped handle for mounting on the front of a dinghy. Use rope to connect the handle to a solid mounting point. I printed this in ABS+ but PETG or ASA would probably work fine too. Make sure you use plenty of walls and…
Print in ABS, ASA or something temperature-resistant. Needs a bit longer screws for the heat-brake fan. And some screws for mounting the fan to the holder + scoop. Update V2: Added version with a top mounted 4010 fan for cooling the…
The model is 325x325 mm, so a large bed printer is needed. I printed mine on a Sovol SV08. Print in ABS or ASA in case the light source is too hot for PLA/PETG. The two sides have a slightly different edge. The one in my photo is the…
Requires 2 pcs M3 heat inserts and 2 pcs M3 round hex head bolts (about 6-8mm).
Replacement rubber cap / knob for the RAM X-Grip mobile phone mount. Print in TPU! The originals are very very squishy.
Prints without supports using the STL orientation. I softened the sharp edges a bit with the butane torch when getting rid of PETG-strings. Update V2: Added a STEP file that has fillet on all edges and a much smoother curve (the original…
Cartoony flower that fits into the top of a pot. Created as a replacement for fake-flowers that kept breaking in the play house. The flower base is made to fit a pot with ca 100 mm / 4 inch opening. Print the flower base with any layer…
Small hammer with hole for inserting an M8x40 bolt as weight for some oomph. There are voids inside the hole for capturing hot melt glue if you really want the bolt stuck in there. But just press-fitting the bolt is probably good enough.…
Vase mode container somewhat inspired by a gooey splat. Print with thick walls in vase mode / spiralize outer contour. I usually go the max allowed by PrusaSlicer, 2.99 x nozzle diameter.
Light and small phone holder with different angle positions. Made for 11 or 14 mm thick phones (The gap is 12 and 15 mm)
This is mostly for fun. I think the original wheels are better at almost everything except looking cool ;D Printing: The tread should be printed in TPU using 0.7 line width and ‘Classic’ wall generator (Set ALL line widths to 0.7mm, this…
Shields the USB-cable from impact and movement which may damage the fragile USB-C connector on the BMPCC 4K electronics board. Only suitable for angled USB connectors. The XLR connector is sadly covered, but the AC connector is still…
Recommend printing with Arachne perimeter generator. Made for 0.4 nozzle so it prints with 3 walls, but 2 * 0.6 will probably work also.
UMM2028 system is just a name to group compatible models. Uses 20 mm horizontal x 28 mm vertical hole spacing. Needs longer than stock screws for mounting to top of stock console. Needs M3 melt inserts for mounting the additional mounts.
The paint palette with my favorite number of wells and brush holders. Prints without a top so it prints a bit faster for me. Also, scraping the paint of the brush against the well-walls works better. This version is not configurable.…
NOTE: New version here: https://www.printables.com/model/967009 Shields the USB-cable from impact and movement which may damage the fragile USB-C connector on the BMPCC 4K electronics board. Only suitable for angled USB connectors. Print…
Holes are 40mm deep, 12 mm diameter.
Try some horns instead of a star on top of your christmas tree this year :) Print with a brim for adhesion - I printed this with the horns pointing up (like the orientation in the STL file)
Water saving lever-button modeled for Ifö Cascade WC. Probably fits some others with the same type of flush handle. Just press and hold - when released flushing stops without emptying the whole reservoir.
Attach using e.g. 40x40mm 3M VHB pad. One at the top is enough, even though two fits. I printed mine in ABS and it has been up for several months. The shelf direction is intentional for ergonomic grip, even though it would have been…
Print in something stiff. I printed mine in ABS-GF25 but I suspect ABS/ASA or even PLA will be fine. The clamp uses a M5 heat insert on the inside of the clamp jaw. Use a bolt to pull the heat insert back down into the hole (You can't use…
Vase mode mixing cup. Use 1 mm bottom and 1 mm outer wall.
A holder for the mod podge starter pack, and some brushes :)
By attaching the “Nut” on the bottom of one of the stools, you can easily stack the IKEA Ibbarbo stools, and then screw the handle down through the stack. Voila - Carrying handle! No supports needed! I printed it in ABS with 4-5 walls. I…
Uses 20 mm horizontal x 28 mm vertical hole spacing.
Printed with 82A TPU, and 50% infill seems ok. With 95A about 25% is better. At 10mm height, go to 0.10 mm layers for better shaped tip.
To wszystkie aktualnie dostępne wyniki.
