Liczymy pasujące modele…
This is an electronic red dot sight for nerf and rival guns. it requires a small LED, a CR1632 battery, and a clear piece of plastic. I tried to keep a similar aesthetic to the original sight. I will post an assembly video soon. please…
Update Log Update 5/9/26 - Added Nightengale, angled talon, and snail talon necks (required a small change in all neck connections), switched to 2 separate printed follower springs + a non-spring follower, and made the clock spring…
UPDATE V2: Added space on the side of the model to make installation and removal easier. I wanted to print an Ender 3 Z-Axis Stabilizer but I did not have the screws for it and I didn't want to go buy them so I remixed it and gave it an…
Upgrade your Nerf Hammershot's power to the right amount for you with these different-sized spring spacers. This model includes 4 different sizes of spring spacers: normal, half-size, ¾ size, and EXTRA STRENGTH!! (I don't know if this one…
(Extended Grip): This is a remix of the Rubber Band Gun MKII by EJTH with a more extended grip. The short handle bugged me especially because the back corner would jab into my palm. So, I made the grip bigger. This model includes the…
Half-dart length APFSDS for Nerf blasters. It has two sabot pieces that form a loose seal with the barrel and then split off after exiting. The dart sits inside and takes a 2mm pin in the front to keep it stable. This of for springers…
UPDATE V2: Added small indents on each side of the barrel to give the darts more space to stick out. This is a remix of deusnefum's uncompensated hammershot mod that's made to work with hitchhiker4200's in-line cylinder. There is also a…
When I printed Bananaperson300 's horizontal printing remix of KaminoKGY 's Ender 3 Belt tensioners re-using the stock screws I found that the fact that both the top and bottom were removed from the puller, let one side of the nut skip a…
What else do I say? It's a no skews direct drive filament sensor mount for ender 3 that I remixed from 3d everything . Prints with no support (check photos for print orientation) and slides right onto the top extrusion. The slideyness…
A round trigger for the SLAB. Prints the same, installs the same, works the same. It just feels better in my hand. Leave any questions in the comments and happy printing!
This shell allows you to fire 2 shots of 3 short darts from Nerf Shellstrike without reloading between. This concept is the same as the 16-shot in-line hammershot cylinder by hitchhiker4200 . The front dart creates a seal with the barrel…
Remix of the mini faux red dot sight by Ehdrien that can attach to the MHP Magpie . Print this out and simply screw it on in place of the rear sight using the same four screws. It prints with very minimal to no supports. If you use…
I randomly found myself wishing that the SLAB had a ball detent system like many of SillyButts' other blasters(Not like it would be that useful, your hand keeps it closed already), but I realized that magnets are way easier. So this model…
UPDATE 3: Widened hole for the filament strand so it can go in easier. UPDATE 2: Added Picatinny variants. (Not yet tested, tell me if they work). UPDATE: Added back sights and the ability to use a bit of clear filament instead of a Lego…
Drop-in replacement for the normal grip, if you don't want the grip shoe. I made this for when I print my own Breacher, but the fact that the original file name is “GripBody_ WithShoe ” made me think that there should be a version without…
This is a trombone trigger. It goes onto the trigger of your trombone to make it more comfortable. You may need to change the diameter of the hole depending on your trombone.
This is a rival rail that glues onto the bottom of nerf kronos. It is easy to print and simple to put together. There is a One piece version and a 2 piece version(the 2-piece takes less supports). Before you glue on make sure you cut any…
The Overheat Drum Belt Holder is a belt carrier for drum mags like the Overheat drum. It uses a catch and release similar to a magwell to ensure that the drum only comes out when wanted. It works with any talon-sized magazine with a…
Cheek rest that can extend 15mm higher than the original and still goes all the way down. Print and use the same as the original. Update: Added one extended by 30mm from the original as the 15mm was barely tall enough.
This Silly Shell uses 17/32-inch brass barrels on the insides for hopefully better performance. You can cut the barrels flush with the shell to let it feed into a Battle Axe, or you can have them stick out for a sniper barrel.…
A remixed version of @galaxyCr8r_248733's Gryphon MP5K cosmetic kit that has a spring-loaded bolt. The bolt prints-in-place with a few supports, and the bolt handle can be slid on. Place a 7x40mm spring in the back, and the rest of the…
This is a remix of a Rival Perses grip that has a spot of a laser diode and a 9V battery. I made this because, with the addition of a hopper extension, I found it very hard to aim(and I thought it would be cool). The 9V batter is friction…
Print normally with no supports. The print slides onto the ends of the cotter pins. The bottom layer is facing outward on the rear cap and the top layer is facing outward on the front cotter pin(This is if you are using the lever pin…
This is a belt mount for mounting speed loaders on belts and other things. These mounts are made to work with the speed loaders by Andrew_Overby and EWguy(links to those down below). It has hinges to hook multiple mounts together. you can…
This is a shim that slides into Warp Saya Mag holders to allow them to fit Nightingale/slim-angled Talon magazines. It is purposefully 1 millimeter too thick so that the front and back of the mag holder keep it in place, but you may have…
This is an add-on to Sillybutts' Wildsyle shell-ejecting pistol that adds a secondary trigger below the firing trigger that ejects the shell. It uses 1x M3x16mm screw at the pivot and 1x M3x12mm screw by the trigger. Install the ejecting…
This is a barrel collet for the Ravion Ontos varient that is shortened by 25mm to allow more room for muzzle devices on a 12inch barrel. I couldn't a SillyButts Spigot Scar onto the muzzle when using a 12inch barrel(default included in…
This is a trampoline net holder optimised to print horizontally. It fits onto 40mm ID metal tubes and mounts a 12mm OD net ring. The fit on the tubes is actually 39mm because my tubes are a little misshapen at the ends, but if the fit is…
I was having trouble feeding worker darts from my Flycore blaster so I extended the pusher by 2mm to fix. Prints the same.
To wszystkie aktualnie dostępne wyniki.
