Liczymy pasujące modele…
This STL is a combination of the top and bottom halves of the original model. I found it difficult to get the top and bottom perfectly aligned when printed in four parts. This is simply printed in two parts (print same part twice) and…
I wanted a custom bookmark for a book I've been reading so I created this one. The far right "E" and "R" have very narrow lines at the top and might benefit from scaling it a bit longer. Added Fusion 360 file if anyone wants to modify…
This is a remix of a perpetual calendar on Thingiverse. https://www.thingiverse.com/thing:398403 Supports should not be needed.
I needed a plug cover for my truck (4 flat trailer plug) and couldn't find any that fit the bill. I cobbled together this version (using Fusion 360) which slides over the plug to protect it. The part was printed in black TPU. I included…
This is my attempt at creating the Star Trek Picard Season Two badge (seen close up in episode 8 around 17:35 or so) The badge is printed with 50% infill and no support. The pin with cross pieces is printed at 100% infill and does need…
I needed to replace a lens cap for my binoculars. I lost the small end cap on my Traq 7x35 set and decided to try and model one and print it out. After some trial and error I got the larger cap made. Both now available. I used black TPU…
My wife broke a nail file handle and asked if I could create a new one. I made the design in Fusion 360. I originally printed it horizontally however this tended to split down the center. I printed vertically and that worked much better.…
This is basically a remix of my other charger stand. My sister-in-law wanted a stand like the other one but the Samsung pad was too big so I modified the dimensions to accommodate the larger charging pad. She couldn't decide on a color…
One piece versions of Deckard's gun stand with and without a base. You will still need the barrel stand from the original version by danielgeez. https://www.thingiverse.com/thing:3272738 The length is almost 270mm which is the max I could…
A remix requested by a friend to make a Deathly Hallows version for their desk. I modified the month ring to use English names rather than a number. The rings were printed by changing the filament once the lettering began and changing…
These are two connectors that screw together. Elastic cord replaces your shoe laces and the ends go through these connectors. Once through you tie a knot in the end so they don't come back out. This changes your shoes to be slip-ons and…
These are clip-on labels for the front of wire cubes. They clip onto the wires and provide a location to add a label. Print Settings Printer Brand: LulzBot Printer: TAZ 6 Rafts: Yes Supports: No Resolution: 0.14 Infill: 100% Filament: […
I decided to build a model rocket but needed a way to attach the fins correctly. I opted for making an alignment jig that would keep the fins equidistant from the body. There are 2, 3 4 and 5 fin versions. The center peg is 10mm in…
I modified the two piece rocket into one item. I resized it in the slicer to 20% (which ends up about 239 mm) tall. The base I made with Fusion 360 as a simple platform with an open area in the middle to put the electronics for lighting.…
Version 2 of the rocket fin alignment jig. This allows several variations of fins from 1 to 12. The fin holder should be printed to the number of fins you intend to attach and they slide into the jig. A central sleeve needs to be printed…
Version 2 of the rocket fin alignment jig. This allows several variations of fins from 1 to 12. The fin holder should be printed to the number of fins you intend to attach and they slide into the jig. A central sleeve needs to be printed…
These are two connectors that screw together. Elastic cord replaces your shoe laces and the ends go through these connectors. Once through you tie a knot in the end so they don't come back out. This changes your shoes to be slip-ons and…
This is a version of K's gun stand as one piece. I had trouble getting the print to work with the tight tolerances so I opted to combine the two parts into one model. You will still need to get the barrel rest from the original model by…
This is a planter and stand I made for my lithops. The depth is about 89mm (3.5 inches) and about 203mm (8 inches) wide. I switched filament for the planter for a two-tone effect. Print Settings Printer Brand: LulzBot Printer: TAZ 6…
Simple upright pen holder. Pen used in picture was 11mm diameter for bottom half. Print Settings Printer Brand: LulzBot Printer: TAZ 6 Rafts: No Supports: No Resolution: 0.12 Infill: 20% Filament: Polymaker PetG Green Category: Office
I wanted a simple cup holder that would hold a plastic glass and keep it from tipping over and make it easy to grasp. Print Settings Printer Brand: LulzBot Printer: TAZ 6 Rafts: No Supports: No Resolution: 200 Infill: 20 Filament:…
I made a model rocket stand to display my Estes Cherokee rocket. It has an Estes "D" engine size top to insert into the engine mount. Category: Hobby
I decided to try and make an arm guard. This was printed with TPU to provide flexibility for fit and ease of printing. No support is needed as the model prints flat. There are four slots to attach elastic ribbon or straps. The openings…
Simple handle for the top of a veggie chopper How I Designed This Designed in Fusion 360 Category: Kitchen & Dining
My wife needed a phone stand for a charger she purchased (Insignia Quick Charger) so I felt none of the available entries on Thingiverse fit the bill so I made one. Works with Insignia phone charging pad (about 95mm diameter) Tested with…
I needed a way to store my ear cuffs and not lose them so I created this. Simple stand with a 9mm diameter center rod that a nut threads onto. Added 2 smaller stands with a smaller top nut. One with and without text. Print Settings…
I recently saw a fireplace phone stand and it got me to thinking about doing something similar with a charger in place. Long ago wanted to create my own animated beer sign since I have several older "bubbler" style signs. This seemed like…
This is a knife sheath made with TPU. This was designed for a 6 inch long blade. The model is 3mm thick and I used a heat gun to fold it in half and bend the belt strap. I drilled holes in order to sew it closed and also used e6000.…
I wanted to try and make arch supports. I have very flat feet and wanted something I could make myself. These were printed in TPU to be flexible. I put them UNDER my insoles and used carpet tape to keep them from shifting. No guarantees…
Simple cup/glass holder to keep them from easily tipping over. I printed this in PLA with 40% infill on the base and 100% infill above the base. Category: Kitchen & Dining
I had emergency disconnections installed but the labels quickly came off. I decided to 3D print some replacements. I changed the filament around layer 17 out of 30 (red to white.) I used PetG and E6000 to stick them to the boxes.…
I had a "Time Machine" rolling ball clock for many years however the PCB board had too many issues and I didn't want to purchase a new clock. I bought a 1rpm clock motor and designed and 3D printed a bracket to hold the motor onto the…
I needed a clip that would hold a water bottle and trash bag during hikes. This works well but typically needs to be clipped on the belt and pants. I printed this in PetG and in the orientation that does not require support. Category: Other
This is a storage box for my CorrectToes toe spacers. I wanted something other than the paper box they came in so I made this. Box top needs to be flipped upside down for printing. Does not require any supports.
To wszystkie aktualnie dostępne wyniki.
