Liczymy pasujące modele…
This latch is very strong to close a closet or drawer with big power. I designed the latch for my closet. Our cats always tried to open the door and do some chaos with our clothings. With this latch the door is always closed.
I had a lot of old cables that I wanted to recycle at a scrapyard. To achieve a better rice, I freed all the cables on the sheath to get the bare copper. Unfortunately, the cheap cable strippers from the well-known online portals do not…
The holder for my body on my TT02 chassis wobbled a bit when driving. To fix this problem, I designed a stiffener. The brackets wobble less and the body sits better on the chassis. The distance between the two holes is 67mm. The diameter…
The original holder presses very the cables of a 2S lipo pack. In the long run, the cable is injured. To get around this problem, I designed a new holder that offers more space for the battery cable. Since it was a good idea to add a…
Rim width 26mm. Diameter 52mm. For example, the tires from Tamiya including foam inserts fit. There are files from offset 0 to 10. For more scale there are files for brake-vents for all offsets.
I drove my rc-car (Carson Virus 4.2 Race) the first time in deep snow this winter. A great problem are the small wheels. I permanently stuck in deep snow and have to pull it out. I searched for a while in the internet for new wheels and…
These tools can be used to fix the camshaft on MultiAir engines and the crankshaft on T-Jet and MultiAir. This makes it easier to replace the timing belt. There are two versions for the camshaft. The version without a pin allows you to…
I drove my rc-car (Carson Virus 4.2 Race) the first time in deep snow this winter. A great problem are the small wheels. I permanently stuck in deep snow and have to pull it out. I searched for a while in the internet for new wheels and…
In order to lay additional cables or replace cables, the covers of the cable duct must be removed. The covers have been glued by Creality and can therefore no longer be used. For this purpose, I designed new covers with matching recesses…
Since I didn't have a real stand for my Xmaxx and I found the original one from Traxxas too impractical, I built something myself. As a template, I took the standard RC car stand. In addition, I modularized the entire booth a bit. This…
I'm not a fan of gluing the electronic components in the rc car. During maintenance or replacement, removal is very tedious and may no longer look nice. To get around this problem, I designed a holder for my current setup that can hold…
These mudflaps prevent excessive dirt from getting to the wishbones and shock absorbers. They fit all Carson Virus models and similar or identical chassis. I printed them in TPU, so they are very resistant to damage.
Sometimes I took some fast food from McDrive. Often some dips are not used and I store these for other meals. All the dips lay in the door from the refrigerator and sometimes I have forgot the dips. With this drawer / sorter are all dips…
My goal was to reduce the dirt which is come into the chassis in heavy dirt terrain. Also the cables from lipos go outside the chassis and hang outside the rc-car. The covers prevent the amount of dirt and hold the cables into the…
The roof from my Carson Virus 4.2 was broken. The original part is made by lexan and is breaking very fast. I designed the roof for myself and make also applications for the hood. I printed all parts in TPU. I think it can not break and…
To prevent excessive wear and tear on the bearings in my rc-basher, I constructed these wheel-balancer. On top speed balanced wheels can calm down the car. I used a thread rods with three bearings from a skateboard or inline-skates. Two…
For my first steps to the smart home, I did not want to invest much and use existing components if possible. Luckily I still had a RaspberryPi Zero with USB-Hat in my craft box. This case / bay can mounted in a 5,25" pc-bay. Hardware:…
This frame can used to adapt a lan-jack cover on a Jung AS500-series-frame.
A rim that is based on the design of the BBS CH. Rim width 26mm. Diameter 52mm. For example, the tires from Tamiya including foam inserts fit. There are files from offset 0 to 10.
With this holder, the batteries can be attached to the compartment with straps instead of the original temples. Similar systems can already be bought as accessories from third-party manufacturers. However, I didn't want to drill into my…
I bought a few lipos a few days ago. The lipos dosn't fit in the lipo-case from my Virus-Buggy. I need a little more wider version from the original case. I designed it new and wided it a little more. I printed the case with petg in two…
There was no room for more electronics in the electronics box of my Carson Virus. Since I wanted to switch my light by remote control, I had to enlarge the box. The box has the same width and height. It has been extended somewhat. It is…
These are all control arms for the Carson Virus (not Truggy). Rear, front, top and bottom. I printed them in PA-CF with a lot of infill and perimeter. After printing, the holes for the rods of the control arm must be drilled out to fit. I…
Another remix with locking recess. I saw the other remix-model to late and remixed the original model quick and dirty. I decide to share this nevertheless with the community :)
With this conversion kit, it is possible to mount the body of the Carson King of Dirt Cage on the chassis of the Virus Race. The conversion kit does not belong to the Virus Buggy or the Truggy. I printed the base plate with many layers…
To give the body more flexibility in the event of rollovers, I designed a new holder. Printed in TPU, it can give way to holders a bit like the originals. The body can also be quickly completely dismantled using the quick-release mount.…
Rear light for the Carson Virus Race to build yourself. The rear light fits my designed flex holder: https://www.printables.com/model/1137403-carson-virus-race-flex-body-holder-quick-release Four red LEDs are needed for assembly. These…
With this holder, the body of the Carson Virus Race and King of Dirt Cage can be held up. For better flexibility, I printed it in TPU.
To wszystkie aktualnie dostępne wyniki.
