Liczymy pasujące modele…
A small case with a push fit lid to fit a pair of CR123 3V batteries. Handy to have around for those cameras that require them - I've found that not all bodies are honest when reporting remaining battery levels and it's useful to have a…
I use Arca-Swiss compatible heads on my tripods and wanted the ability to mount my GoPro Hero7 easily without hassle. At the time of designing this I couldn't find any other alternatives that mad me happy. An additional M5 (0.8mm pitch…
A drip lid for 6" pots to allow for the water supply to reach a larger range of the growing medium. Takes a 4mm inner diameter tube, inlet is 5mm to allow for a bit of stretch. I was asked to print…
An 80mm² lens-board for the Horseman 45FA field camera with a Copal #0 (34.6mm) opening. This is modelled as accurately as possible from an original piece. There are 2 sets of files here - one I originally did in PETG and then a later one…
An 80mm² lens-board for the Horseman 45FA field camera with a Copal #1 (41.6mm) opening. This is modelled as accurately as possible from an original Copal #0 lens-board with a modified opening. Print instructions Printed in PETG 0.1mm…
I purchased a second-hand Paterson Super System 4 Daylight Developing Tank that came with no lid. I didn't have an original to copy from so I chanced it with this and it works pretty much perfectly. Printed in TPU Print instructions…
A small handle to clip onto the lid of your turntable so it can easily be lifted & lowered with a finger. I found that the lid of my new turntable would lift up one one hinge or the other, meaning I would have to lift the lid from both…
A replacement seal for the Paterson System 4 Tank. It's a good push fit and best printed in flexible material. Print instructions Printed in TPU. Variable layer height - 0mm to 3mm – 0.3mm 3mm to 12mm – 0.15mm 100% infill Had better…
My makerspace salvaged an HP Designjet 500 plotter that came with no accessories. Ordering a 24" roll of paper to test it with, we needed some way of feeding the roll into the printer. You'll need two of these per roll, and a suitable bar…
An 80mm² lens-board for the Horseman 45FA field camera with a Copal #1 (41.6mm) opening. This model has a 12mm extension on the front to allow better access to the controls of a given lens should it be required. This is modelled as…
An 80mm² lens-board for the Horseman 45FA field camera with a Copal #0 (41.6mm) opening. This model has a 15mm extension on the front to allow better access to the controls of a given lens should it be required. This is modelled as…
A replacement lid for the Paterson System 4 daylight film developing tank. Printed in TPU. Quite a tight fit, still a tiny bit leaky but I've found these tanks always were. Print instructions Printed in TPU 0.3mm layer height, 100% Infill…
A replacement diffuser for the Nikon SB24 Speedlight. A push fit that doesn't fall off easily. For best results print in a white PETG with a low layer height (max 01.5mm). Print instructions PETG 0.15mm layer height 4 perimeters Infill…
Needed a pen holder for my whiteboard. I had four big boys and four small boys, so I made my own.
Owning several Cotton Carrier hand straps for my camera bodies already, I wanted to use the plates that came with them without the hand strap attached for some applications where it would get in the way. During the lockdown I had no easy…
I've purchased a couple of older-style Gitzo tripods in the past for repair whose top plates are either missing or are broken. For replacement plates, this is available either as a two-part print or a single object. The plate is…
To wszystkie aktualnie dostępne wyniki.
