P
Printablesfpvgio
Official ImpulseRC Apex Printable Files
Official 3D printable files for the ImpulseRC Apex frame!
- Pobrania
- 271
- Polubienia
- 15
- Ocena
- 0
Wszystkie modele
Liczymy pasujące modele…
P
Printablesfpvgio
Mobula8 DJI 04 Lite Canopy
tpu 50%infill - weight with 04lite = 21g. 0.2mm layer height organic supports should fit original 04 lite camera faceplate & and axis flying 14mm camera housing. install your camera first and run a small zip tie through the spaces at the…
- Pobrania
- 222
- Polubienia
- 18
- Ocena
- 5
P
Printablesfpvgio
Pavo Pico Walksnail Avatar Canopy
Designed to be easy to print with no supports or brim. Print at 90-100% infill with PLA+. You'll want the gummies in your unit. I found the easiest way was to use fine point tweezers to start them in the holes and then your fingers to…
- Pobrania
- 130
- Polubienia
- 9
- Ocena
- 0
P
Printablesfpvgio
Prop-Unstopper
Because everyone's printer has slightly different tolerances/clearances there are two versions of this in the files attached.Moreover, if the loose is too loose a single layer of painters tape with make them snug (as pictured.) If you…
- Pobrania
- 118
- Polubienia
- 18
- Ocena
- 0
P
Printablesfpvgio
Quadmula Siren F5 & F3 Walksnail Avatar Dual Antenna Mount
UPDATE 01.18.25 I still haven't figured a good tolerance because the TPU absorbing moisture and expand. It seems that no matter what clearance I give it it will still absorb to be snug after a few months. The only solution I found is to…
- Pobrania
- 112
- Polubienia
- 9
- Ocena
- 0
P
Printablesfpvgio
Quadmula Siren F3 GPS mount & other lightweight parts
Thinned up the stock armguards and front bumper from Quadmula, made a superlite gps holder for the Flywoo GOKU GM10 Nano V3 GPS. The GPS holder comes in 3-different thicknesses 0.5mm, 1.0mm, 1.5mm If you want something designed for the…
- Pobrania
- 108
- Polubienia
- 5
- Ocena
- 0
P
Printablesfpvgio
Goggles X Front Plates
Printed tilted forward 45° with organic support on build plate only and at a 2.8mm layer height. Use M2 screws or e6000 to attach to the front of your Goggles X. The VRX cover uses an iFlightVRX, Runcam Cam Mini DVR, 20x20x6mm 2wire 5v…
- Pobrania
- 38
- Polubienia
- 5
- Ocena
- 0
P
Printablesfpvgio
TBS Unify PRO32 nano BETAFPV Canopy Mount
Weighs 0.26g Printed at ultra detail took 7mins. Added a tab to heat shrink the VTX's antenna to. I glued the edges of the TBS Unify PRO32 nano VTX to the frame with e6000 and let it dry over night. Pictured is the frame next to the…
- Pobrania
- 33
- Polubienia
- 3
- Ocena
- 0
P
Printablesfpvgio
Googles X Strap Adapter
Printed in TPU at 90% infill. Should stretch to fit through the Google strap holes. Feed loop side in first from the front. Be extra gentle with the plastic on your goggles
- Pobrania
- 17
- Polubienia
- 1
- Ocena
- 0
P
Printablesfpvgio
Whip Antenna LHCP/RHCP Converter
A converter made by following the instruction of this VAS- Video Aerial Systems video. https://youtu.be/n-ngHnxWPaY?si= It seems they offer a similar higher quality product based on the same ideas in the video, but in a much smaller and…
- Pobrania
- 15
- Polubienia
- 0
- Ocena
- 0
P
Printablesfpvgio
Pizza Box Gate Stand
Accessibility is important to me. Most local libraries have free 3D printer access these days. With a free library card and some boxes you too can practice for the next whoop race. Hope you enjoy!
- Pobrania
- 7
- Polubienia
- 0
- Ocena
- 0
To wszystkie aktualnie dostępne wyniki.