P
PrintablesCheruTijntje
Wallmount Bosch E-Bike Charger 36-2/100-240 - with only two screws
Wall mount for Bosch e-bike charger 36-2/100-240 mounting by means of 5 countersunk screws.
- Pobrania
- 363
- Polubienia
- 23
- Ocena
- 5
Wszystkie modele
Liczymy pasujące modele…
P
PrintablesCheruTijntje
Gaggia Classic - Steam handle
Steam knob for Gaggia Classic pre-2015 model with 6 mm hole with flat side. It is a very tight fit, just push on hard! The flat side is internally reinforced.
- Pobrania
- 319
- Polubienia
- 27
- Ocena
- 5
P
PrintablesCheruTijntje
Gaggia Classic - Scale Extention
I really like this extension because you can take out the scale to use on the counter and the drip tray just rests on the sides of the base. It is a low profile drip tray, I need to drain it after each flush-brew-flush cycle. Cleaning is…
- Pobrania
- 254
- Polubienia
- 69
- Ocena
- 5
P
PrintablesCheruTijntje
Cessna Yoke
Because I didn't like the size of the existing yokes I made this one myself. Also as a bit of training in Fusion360. The center column is universal and does not contain any fitting for connecting an axis. So it is not ready to print…
- Pobrania
- 182
- Polubienia
- 19
- Ocena
- 0
P
PrintablesCheruTijntje
Large volume driptray for Krups Essenza Mini XN110x
The Krups Essenza Mini comes with two tiny driptrays. One is full after two cups of coffee, the other is always near empty. So I created a single compartment which does fit the original parts.
- Pobrania
- 141
- Polubienia
- 12
- Ocena
- 5
P
PrintablesCheruTijntje
iPhone 13 mini wireless charging dock, for iOS17 Standby mode
Nice nightstand charging dock for the combination of: iPhone 13 mini Otterbox Symmetry Belkin BoostUp Wireless charging pad 10W
- Pobrania
- 135
- Polubienia
- 19
- Ocena
- 5
P
PrintablesCheruTijntje
Press/Tight/Loose-Fit Offset Gauge (0.05 mm increment) / Tolerance test
Tool to see what the margins of the printer and the used filament are in order to create perfect press/tight/loose-fit parameters. Update 2023-05-20: added 0.05 offset to Window and to Pin
- Pobrania
- 99
- Polubienia
- 4
- Ocena
- 5
P
PrintablesCheruTijntje
Gaggia Classic - PID Top
Extention to go on top of my Gaggia Classic Espresso maker. Uses the original lid and water duckt. The water extention pipe needs some rethinking, it is not very good. The top contains (from left back to front to right): -DPDT Switch for…
- Pobrania
- 89
- Polubienia
- 9
- Ocena
- 0
P
PrintablesCheruTijntje
Simple phone stand
Minimalistic mobile phone stand to insert your mobile in. To be used for easy reading or watching while sitting at a table. The opening width is 13 mm, on one side the angle is 45 degrees on the other 60 degrees. In your slicer, position…
- Pobrania
- 83
- Polubienia
- 10
- Ocena
- 0
P
PrintablesCheruTijntje
Gaggiuino Top
Gaggia Classic housing extension to fit touchscreen of the Gaggiuino project on front of the machine. This top fits the screens baseplate of ‘ Gaggiuino - Gaggia Classic | Pro Touchscreen Housing and Funnel Plate Mount ’.…
- Pobrania
- 77
- Polubienia
- 15
- Ocena
- 0
P
PrintablesCheruTijntje
Leo Bodnar BU0836A Case
I have created a very tiny case to protect the BU0836A print in my flight yoke. There aren't many cases to find so I uploaded it. I made it on a Bablulab P1S with at max a 0.2 mm tight gap between the parts.
- Pobrania
- 76
- Polubienia
- 2
- Ocena
- 0
P
PrintablesCheruTijntje
TinkerTop
-This is still a work in progress, some things will change in the future- TinkerTop is a Gaggia Classic project that can be added to the Gaggia Espresso machine to add a place for modifications. The goal is to make a universal base to…
- Pobrania
- 42
- Polubienia
- 3
- Ocena
- 5
P
PrintablesCheruTijntje
Eureka Mignon Specialita Singe Dose Conversion
I only use my grinder for single dosing and have been using this mod for well over a year now. It is a joy to use and the retention is only 0.3 grams (3 beans).
- Pobrania
- 17
- Polubienia
- 3
- Ocena
- 0
P
PrintablesCheruTijntje
WeighMyBru² without screws - REMIX
I have made a remix of this fantastic project to fit my needs. I strongly advice to print partial test pieces to test the fitting for your printer. My printer has a rock solid "snug" fit with a 0.2 mm margin. It is still a work in…
- Pobrania
- 16
- Polubienia
- 8
- Ocena
- 0
To wszystkie aktualnie dostępne wyniki.