Liczymy pasujące modele…
This is a remix of my PrintDry Pro spool adapter (which in turn was a remix of a Thingiverse design by Skrutt84: Ender 3 - Filament holder DELUXE). This winder will fit spools with center holes up to about 80mm diameter. Use with a…
This is a replacement batter cover or cap for Mitutoyo Calipers model 500-138. The identified Thingiverse model was used as a baseline for this remix. I used eSun PLA+ as filament and it seems to be robust enough for the small clips on…
This thin nozzle tip fits a 3m marine silicone 3 oz (88ml) tube, but will likely fit other tubes (silicone, grease, other sealants, adhesives, etc.) of similar size or shape. The nozzle tip is quite fine (i.e. small outlet diameter) for…
Just the refined spacer stl to reduce the side air gap further using the same design but stretching it out some more. Everything else is the same. Only uploaded the one stl file, so just mirror it in the slicer to print both sides. Note…
Remix of original dryer pod with a tab to make handling easier. Print as you would the original design. No supports required. October 6/23, V1: Feedback was that the tab connection point was weak due to the thin walls of the pod. This…
I have my X1C on a low table with plenty of room for bin to collect filament ‘poop’ on the floor behind the table. However, I did not want to push the X1C to the back of the table as it would somewhat restrict the access from the front.…
Just a simple remix of Wickedbanana's tight fit case to add a hole so the Apply symbol can be seen. I still printed it a 99.5% scale to make it a little tighter on the phone. Seems to fit quite well now…have been using it for several weeks…
This is a split pottery mold, containment ring and clay pestle for one half of a 52mm diameter ball. The containment ring is used to hold the two pottery mold halves together, and the pestle is used to press and shape the clay within the…
A remix to do a few things… 1) I closed the vents behind the hygrometer. My view is you want the hygrometer to measure average air humidity in the AMS, not the air right at the silica beads…which will typically read lower levels of…
The PrintDry PRO filament dryer includes a couple of rubber adapters for different size spool center holes. However they will not fit spools with large center holes. This adapter will fit most spools with center holes up to about 80mm…
To print the canopy, print it vertically with the nose on your bed. I used slim tree supports and it worked out very well. For info, I printed the canopy at 0.16mm layer height and the grommets at 0.2mm layer height. Use 3 perimeters or…
I liked the veroni case by Link Designs. However the rounded sides led to some artifact issues near the bottom of the case. Likely due to the slope of the sides at that point. Therefore, I combined the Link Design case with the one by…
Another set of small mounts to use with zip ties. These are small mounts, but regular size zip ties will fit as opposed to just the smaller pico size zip ties. Included are both mounts with countersunk screws and plain. If using the plain…
Introduced 2 layers (0.4mm total) as first layers printed that can be colored for the white of the bunny, the eggs and lower background. Upper background remains clear. Overall height of the bunny solid areas and frame lowered to 1.2mm…
Designed a simple clip on weather shield for the outdoor WYZE camera. Helps to keep raindrops off the lens. Printed in 0.2mm layer height with 3 perimeters and supports. Used a modifier to have the arms at 100% infill, 25% for the rest. I…
The Starlink Antenna base (Standard Antenna) is made of metal, and could possibly scratch painted surfaces or fiberglass. These protective feet fit over the 4 ends of the base and protect the surface the base sits on. I used TPU to print…
To wszystkie aktualnie dostępne wyniki.
