Liczymy pasujące modele…
my son was short a couple track pcs' so I took it upon myself to try and make some… after about 9 prints of trial and error.. this one is not too bad… if you print with a smaller nozzle and fine detail it will probably turn out better…
lost the original drain adapter, so in making one I created the cap to test fit.. works great can use a small rubber washer or o-ring.. or just the cap, as our pool has a valve to be pushed in order to drain so the cap doesnt really need…
trying to organize the drawer by hanging the most used cords by the USB block
I've missplaced my original pool drain cap to garden hose adapter so I created one that may not look like the original… but it works. from what I've read online.. its the same as a few others.. like coleman
Just more practice on the fusion 360 program and learning more about shapes and 3D printing. I reduced the bowl by 50% for the one printed in the photo. which took about 1.5 hours on my V400.
I'm pretty good at “miss placing” things.. so I made this to hold the sensor on the printer…
needed a new nerf bar for my Slash RC car and drew one up with some additional strength and it seemed to work great.. now I just have a few on hand when we go driving
I was tired of our blocks being in a bag so I created a box with lid to store them and now it's easier to store on the bookshelf.
I was looking at all the great ideas for flying things and in discussing them at work a friend mentioned the seeds from maple trees.. so I drew a similar shape based on them and added a hook for launching. I printed this one with the iron…
I used the iron filled PLA for this print as I wanted the lock to be rusty.. it's a fake lock for a train car to be smashed by an actor on the TV show i work on. I used vinegar/salt/hydrogen peroxide as the solution to make it rust. it's…
this was a temporary handle for our cupboards while we decided on what material and style we wanted in metal. the handles have been on for 3 years already… not very quick on making a decision. the hole spacing was taken from a store…
my son wanted the body lifted a bit.. so I dont need an excuse to practice drawing and came up with this. its about 3/8" higher than original
I drew up and tested a few of these and the last one seemed to fit best. I used PETG with15% fill and I had the model standing up to avoid any supports removal issues.
I did a two color version.. I believe it was layer 11 where the color change takes place. PLA settings. I used a v400 for this print at about 39 minutes total
i needed a spot to mount the new ESC from injora and also the receiver on my TRX4M chev truck. this is just a plate that bolts where the old ESC/receiver combo from Traxxas went.
6" self watering plant pots with tight lower trays. I dont have a watering can that fits. and it can get a bit dicy trying to pull the bottom off to fill it up..
I have a couple of these around the shop. one at the lathe and milling machine and one on my tool box.. I now look for sharpies much less than I used to.. uses a ½" x 1/8" magnet x2 . I may update it to use 3 or 4 magnets.. but it works…
since I have broken the stand that came with the V400 I wanted to clean up my desk a bit.. and practice drawing, so I made up this bracket to mount the V400 pad to on the extrusion of the printer.
I needed storage for my milling machine collets, so I drew this up and printed it on my XL. turned out great, now I can have them organized in a tool box or by the mill.
I made this to keep the earbuds on my neck better when I'm at work or the gym.. they would always fall to one side and then off my neck all together. this clip keeps the earbud wire in one spot, mostly, and is MUCH better at staying in…
I just made this last week to make some space on another shelf in the shower.. I had a couple leftover suction cups. I believe the dollar store has a large selection. its about 2" in diameter with a 3/8" nipple on it Feb 1 2025 - after…
I was just messing around with drawing again. created a TURD for my FORD
I saw lots of videos of people with venturis on leaf blowers and I'm always up for a challenge for drawing in Fusion.. so drew this up and printed it in ABS. seems to work alright.. definitely made a difference with it on
I made this to fit the holes that exist in the enclosure and I used some spare fasteners from the enclosure build. works great. there are slots to put the square nuts into then the m3x4mm screws are what I used next version will be…
was looking to practice drawing and printing.. this turned out to be a great addition to my desk. final item is slightly larger than a CD case .. no special settings.. 3 parts
needed a wall hanging (or side of toolbox or lathe) holder for the Allen keys. also to practice drawing.
looking to make a different style buggy and the flintstones came to mind. used support from buildplate only. and it worked out well.. i used PETG.
the adapter that came with my shop vac wasnt quite small enough to get into the slots to clean out the chips.. so I created this one to get in there.
I wanted to make a prusaslicer themed coin/token it is 1.5" in diameter
wanted something simple as a gift for my family.
I wanted to use the stock battery holder so I drew up an offset version mount for it and it seems to work. no special functions on the printer.. I used PLA and organic supports from bed only.
was kind of tired of locating the build plate on my V400, (its not bad..but..) so I practiced some more drawing and came up with this. I will add 2 sided tape to lock it in place.. but it works as is.
was looking for a small driver bit holder to get into tight spots… didnt have one, so I drew it up and printed it.. works great. sorry I didnt include the .STL.. I'll load it ASAP
was given an opportunity to build an organizer for my desk, and to continue learning how to draw with fusion 360. and with 3 printers at my shop… it only took a few hours to build the whole thing.
wanted a “hang loose” logo that could dance on the dash of the car… shakes really well.
running with a theme here and making this version a “horns in the air” to metallica and more.
looking to keep practicing the CAD program, so these contests are great for that. so many great ideas.. this thimble was just a good excuse to draw. after I printed this.. I realized that using PETG would have been better for strength at…
I needed a way to create a support on a camera cart without taking any more room on the cart itself.. so I made these wedge clamps with recess for 3/8" nut and used all thread with a washer to tighten the “spud” or monitor mount to the…
need a place to access sharpies? here you go.. on the qube 500 case.
model by amish_rabbi
I wanted to practice drawing again in my CAD program.. so I created this cookie cutter for a friend. It was based on a photo of the dog.
wanted a hot wheels knob on the printer .. I didnt have multi color filament on hand.. so It's just black in the photo.
great models for the RC community. Thank you
I had a rotor with a fairly serious bend in it, so I drew up a mount and made it for the lathe so I could use a dial indicator and 'tweak' the rotor bit by bit I used a 1/2 bolt that was long enough to be clamped into the chuck of the…
To wszystkie aktualnie dostępne wyniki.
