Wyniki wyszukiwania: 1811

Sortowanie

Liczymy pasujące modele…

P

Ryobi Charger (RC18115) Wall Mount Cradle

This solves for the odd annoying geometry of this charger so you can mount it to the wall, like most of the other chargers allow. It sits nicely without any kind of adhesive but if you want a more secure solution, double sided tape or hot…

Pobrania
699
Polubienia
68
Ocena
4,78
P
Printablessamywamy10

Ryobi One+ IntelliPort Battery Charger (RC18115) Skadis Holder

An Ikea Skadis mount for the Ryobi One+ IntelliPort Battery Charger (RC18115)

Pobrania
149
Polubienia
23
Ocena
5
P
PrintablesSvenson

BMW Cable Holder 33181181218

This cable holder replaces the BMW OEM clip 33 18 1 181 218 (33181181218). It routes and secures wiring on the suspension—typically the brake pad wear sensor at the rear, and in some models also ABS/signal wires—so cables don’t chafe or…

Pobrania
106
Polubienia
15
Ocena
0
P
PrintablesHannibal

DIY iMac Late 2014 5K monitor kit for R1811 driver board

To convert my iMac Late 5K 2014 into a 5K monitor I used a Stonetasking R1811 driver board. Most of instructions here can be applied to other iMacs and other driver boards as well. Note, that my particular iMac is one with a factory VESA…

Pobrania
102
Polubienia
10
Ocena
0
P
Printablesjorycz

iMac 5K Display - R1811 Driver Board Holder and Pads

This part helps to convert your old iMac to 5K Display. How to do it is here https://github.com/jorycz/iMac-5K-display-convert This part is R1811 Driver Board Holder with Pads. Print it using PETG because of slightly higher temperature…

Pobrania
72
Polubienia
3
Ocena
0
P
PrintablesYuri Makassiouk

Ryobi Charger (RC18115) Wall Mount Cradle Remix for Multiboard

Attaches the RC18115 to Multiboard with 4 screws (You will need 4 - actually 2 might hold just fine - of those: https://thangs.com/designer/Multiboard/3d-model/13%20mm%20Small%20Thread%2C%20Flat%20Head%2C%20T-Bolt-974236). I printed it…

Pobrania
69
Polubienia
8
Ocena
0
P
Printablesjorycz

iMac 5K Display - R1811 Control Strip Case

This part helps to convert your old iMac to 5K Display. How to do it is here https://github.com/jorycz/iMac-5K-display-convert This part is Case for R1811 Control Strip where is status led, IR port and control buttons. Can be printed…

Pobrania
50
Polubienia
4
Ocena
0
P
Printablesengineer27

Replica of Elan/Heritage Lord of the Rings 1811A

This is a replica of a classic figure from the Elan Merchandise Lord of the Rings line, "Saruman's Urak-Hai Orcs of the White Hand Clubs" pack number 1811. Heritage Miniatures manufactured these figures for Elan, who held the LotR license…

Pobrania
24
Polubienia
5
Ocena
5
P
PrintablesChad Cooper

BMW MINI 12mm Blind Blanking Plug 51718110199

Replacement for 12mm plugs on BMWs and Minis. These are usually found on the inside of doors. A couple of mine were missing so I reverse engineered from one which was still present. Print with TPU or TPE. TPU was fine but I'd also quite…

Pobrania
17
Polubienia
1
Ocena
0
P
Printablestangcla

Eitech 1811 connector

Connector from an Eitech construction kit (part number 1810). Category: Construction Toys

Pobrania
17
Polubienia
1
Ocena
0
P
PrintablesNeilandPaul

Retaining ring for Stanley SL18117 Wet/Dry and similar Vacuums

Retaining ring for use with Stanley SL18117 Wet/Dry and similar Vacuums. This holds the Stanley 25-1217 Reusable Dry Filter in place. Note that the Reusable Filter must be used with Stanley's 19-1600 Foam Filter. This filter combination…

Pobrania
11
Polubienia
1
Ocena
0
P
PrintablesHRicK93

Somfy TaHoma Smoke Alarm (1811483) Cover

Cover cap for the Somfy TaHoma fire alarm (1811483) which looks a little better than the original square version. Printed with PETG. Everything has been tested and works perfectly.

Pobrania
9
Polubienia
1
Ocena
0
P
PrintablesMark D

iMac 5K Monitor Conversion - R1811 & R1820 Mount with Hole

This is a 'pocket' style mount for the R1811 or R1820 board, used in the iMac 5k monitor conversion project. It snaps into the ram cover door, and then the board slides into the print. Using friction and right angle adapters, the board…

Pobrania
3
Polubienia
0
Ocena
0
P
PrintablesMark D

iMac 5K Display - R1811 Control Strip Case Improved Back Panel

This contains just the back plate for the original model, which is a small cover for the Stonetaskin R1820/R1811 control panel board. This back plate has a couple of pegs to hold the board in place, and the ridges keep it snug to the…

Pobrania
2
Polubienia
0
Ocena
0
P
Printables

Somfy TaHoma Smoke Alarm (1811483) Cover

Cover cap for the Somfy TaHoma fire alarm (1811483) which looks a little better than the original square version. Printed with PETG. Everything has been tested and works perfectly.

P
Printables

BMW Cable Holder 33181181218

This cable holder replaces the BMW OEM clip 33 18 1 181 218 (33181181218). It routes and secures wiring on the suspension—typically the brake pad wear sensor at the rear, and in some models also ABS/signal wires—so cables don’t chafe or…