Lego Compatible (2853.dat) Technic Engine Crankshaft
This model is compatible with the lego system.
- Pobrania
- 894
- Polubienia
- 60
- Ocena
- 5
Liczymy pasujące modele…
This model is compatible with the lego system.
This model is compatible with the lego system.
Tow hook cover at the front as it is no longer available, a 3D part was made. not quite original but good enough. PETG printed.
This model is compatible with the lego system.
This model is compatible with the lego system.
Print it with FLEX!
Es empfielt sich ASA.
The title says it all. This box will hold three of the four tips that go on the heat gun and have a small area for the extra nuts and screws. The presumption is that the fourth tip is on the heat gun itself. The box is built using the…
Rugged box for your precious Hazet tools. Should work with every toolset that comes in the 165-S box, like most ¼" toolsets like 853 and 854.
Replacement tine pivot clip used for some Jenn-Air, Kenmore, KitchenAid, LG, Maytag, and Whirlpool dishwasher models. Directly Replaces: WPW10082853, W10082853, WPW10082853VP, SAPW10082853, 1446946, AP6014920, AP4262208, AH1734891,…
The case is made for a cheap popular video surveillance board from Aliexpress (46х118mm 9CH NVR). To store the recording, I use an old solid-state hard drive without a case 65x42 mm. This model does not use screws. Assembly sequence:…
Preizniet/mutter OEM 853.873.139 Spreizmutter zur Befestigung von Anbauteilen z.B. Grill und Schweller oder Spoiler. passend für: Golf I Cabrio, Mod. 1988-1993 (Kühlergrill) Passat 32B, Mod. 1985-1988 (GT-Verbreiterungen) Polo 86C, Mod.…
These are clipper guard holders for Moser 1170 1230 1233 1234 1400 1853 1854 1855 1870 1871 1872 1873 1881 1884 trimmers/clippers The guards originally came loose in a bag making it difficult to find the specific size needed. These…
The name Horch was synonymous with regal, sophisticated, and elegant design in automobile industry during the 1930s. With the type 853, the Zwickau-based car manufacturer probably introduced its most remarkable model to the public in…
Its loose recreation of original part 8N0853586A. May need some tweaks depending on state of your car body.
Avant TDI Logo im Retro RS2 Look. Ersetzt das Quattro Logo mit der Teilenummer 4F9 853 736.
A pencil/pen vase to keep your favorite pens and pencils in. It is 111mm tall and 81mm for the x and y axis. The photo shows the vase printed in vase/spiralize mode with 1 wall and 3 bottom layers. The stl file is solid. It prints great…
Ich habe die Originalclips für die Halterung des Kühlergrills vom Audi 80 B3 nachgebaut. OEM 893853663A
Abdeckkappen-Unterholmverbreiterung OEM 321 853 140A Passat 32b GT "Schwellerverbreiterung"
Ich habe auch den Passenden Schlüsselanhänger dafür ;-)
Loose recreation of existing VAG part 1H0853586. May require 2%-3% scale up in slicer depending on your printer and filament. Flexible materials strongly recommended.
cover for the pillar between the doors
Thule Convex Washer Part # 853-1317-04 from 400 XT roof rack system
This is a pair of holders for the double-sided sharpening stone that Norton makes for axes and hatchets. I couldn't make up my mind whether I wanted to store this vertically or horizontally, so I made both. The bottoms of these differ…
Adapter for Maktec L1853 battery. Category: Tools
As it is rare to find nowadays, I made a copy of an original Thule 853-1388 cover thing and made it to fit better to a cheap aftermarket lock cylinder like this :…
I have not extensively tested this, but it clicks into place and the drawer operates properly. I added features to register in slots on the slide, including a pin where the OEM rivet was. I printed in PETG, but for best durability, I…
ABS, ASA I used 4 shells 40% infill .2 layer hieght
When getting my mower ready for Spring, I noticed had a fuel leak on my 23HP kohler courage engine riding mower. Fuel would weep up the screw holes and out the sides. I pulled the carburetor off and nothing looked wrong. Only after i…
Simple solder spool holder for a Yihua 853D SA II solder station
It is a common issue, that the rubber stop for the rear seats gets worn out and it leads to slack in the latch. You cannot buy the rubber stop anymore, so I designed it in CAD for you to print in TPU. The replacement part number is…
I made this case for an Acer Chromebook that had a broken display. The case is split into two parts, so it fits on a smaller print bed(i have an A1 mini), but optionally you can edit the model and combine them. I used PETG to print. The…
Add a touch of humor and personality to your home! With a purple base and bright yellow chicken feet, this eye-catching pink coaster will transform your speaker into a unique decorative element. Original, playful design.
The freezer lid broke, so I decided to replace it by designing and printing a new one. Attached are the freezer lid models: one designed with a slot to glue in a gasket, and one without. An example of print orientation is also included.…
Ich habe auch den Passenden Schlüsselanhänger dafür ;-)
When getting my mower ready for Spring, I noticed had a fuel leak on my 23HP kohler courage engine riding mower. Fuel would weep up the screw holes and out the sides. I pulled the carburetor off and nothing looked wrong. Only after i…
I have not extensively tested this, but it clicks into place and the drawer operates properly. I added features to register in slots on the slide, including a pin where the OEM rivet was. I printed in PETG, but for best durability, I…