Liczymy pasujące modele…
Introducing the Broadhead from Horizon Zero Dawn! This machine is to scale with the official board game and stands on a 40mm base. It is intended to be printed in one piece with the base attached for stability. All credit for character…
A tiny bit larger than the SKB case to improve the fit in the SKB bowcases. The original SKB box slides out pretty much every time, mine doesn't.
This is a 3 piece broadhead design. Apply super glue where necessary and assemble. Print instructions Layer Height: 0.15mm Infill: 15% Perimeters: 2 Brim: Yes, 2mm width Filament: PLA These setting work well for printing the model.
Some broadheads for arrows. The original typ is 8mm diameter and the shaft is 7mm. They actually work :D. Print instructions Used PLA and it works. You can use whatever you want
I remixed this to make it 15% larger to accomodate larger broadheads. It should still fit smaller heads too. I also adjusted the clips and hinge bars so they clip in and pivot better without falling out. 10% infill. No supports (used…
An Improved Broadhead box. The lid is a friction fit so your tolerances need to be dialed in. DO NOT close the all the way when empty you will not be able to open it again. EDIT: I added 2 new lids v2 that have finger cutouts to make it…
A no-nonsense broadhead wrench designed for bowhunters who want reliability and ease of use straight off the printer. This support-free design is optimized for 3-blade and 5-blade broadheads, but it’ll still get the job done on 2-blades…
Works well in PLA at 20% infill, or 100% infill. Makes it extremely easy to install broadheads on any arrow. Rotate your broadhead within the wrench to find the appropriate slots.
Used for sharpening removable blades on a broadhead. You will need to source a flat surface with a honing stone or wet-rub paper to do the job properly.
Simple Broadhead storage tubes. Standard broadheads thread into the lid via friction, there are no actual threads. When printing the six count box use two 3 count lids. I included single counts incase anyone wants to create their own…
I am sure the Magnus version works just fine but I couldn't find any in stock and decided to just make my own. I used a piece of scrap from a Goldtip Hunter shaft that measured 7.6-7.7mm in diameter and glued it in the end. That way it…
Very slight modification to the original broadhead wrench. Added chamfers so the wrench can be printed front side down. This model may be easier to print in this orientation for certain printers. I believe the original model was meant to…
This is a latching box for storing three Ravin R101 Broadheads . It prints in one piece, without supports. I added a bit of foam to make it silent and to hold the broadheads in place. It probably works for aluminum (R102) and titanium…
Some bow travel cases don't have plastic injected holes for screws which I recommend as the best way to add this mini box. If the orientation is not lining up horizontally or vertically so that the screw holes don't match up on the lid of…
Clip for use on a "Rage" type broadhead Demo here: https://youtu.be/v_DGXT3TEos Category: Sport & Outdoors
Added the ability to grab the broadhead base by the bottom by using thumb and index finger, or by using pliers or other tools. You can also push the base down through two holes in the lid. The original creator mentioned a possible issue…
I needed a wrench to tighten the broadheads on my arrows. I created this and printed it in ABS with a 25% infill. I used a brim and had no issues. This updated version will fit both fixed blade and mechanical. Printer: Core One Filament:…
Just glue these two inserts into a cut off arrow shaft to make a handy broadhead sharpening tool. Currently sized to fit a 2219 shaft. More sizes to come Insert is not threaded. you can thread a head into it, but it is friction fit. Print…
A sharp, modern broadhead I designed from scratch . The blade are hollow diamond frames around a central cylindrical ferrule, with a tip that comes to a clean point. It works as a display piece, cosplay or film prop, desk ornament, or…
Quick and cheap way of removing your broadheads
This is the first iteration of my design on a case for the G5 Mega Meat and Dead Meat, With V2 I changed the hinges, updated the sliding lock, and added weights to the top lid for identification between broadhead weight. If you have any…
I made this for a trade show but some may want to display interesting broadheads. I removed the text on this, but you should be able to add text in your slicer.
