Liczymy pasujące modele…
Tablet clip for Sportop E850P Elliptical, use tablet while training. I use 18mm variant for iPad Air in a thick case, use other variants for different cases / devices. Printed in PLA, to connect it start from the bottom, then clip on top.
Wydruk około 0,36 €–0,44 € nettoWstępna wycena jednego wariantu
BMW Z4 E85 Easy to print . Of course you can scale it the size you want. Easy to print for up to 90cm length, just cut it in some parts with the new slicer. I recomend a strength of about 2-3mm. Add some double-sided tape and stick it on…
This is a phone holder for a Samsung Galaxy Z Flip 5/6 to allow you to take advantage of the cover screen in the folded position and use your favorite navigation and audio apps in a 2002-2008 BMW Z4. The mount is cut away on the sides to…
Original cover was warped, so i made a new one. v3 - fixed incorrect location of the hole for screw. v2 - after printing, noticed small reinforcements are no necessery and make cover warp. after removing them everything looks ok.
Key tag in the shape of a BMW Z4 E85 phase 2
Easy to replace your Washer Cover. Print left or right side cover. Paint it. Pull out the Washer System with your fingers (that's the hardes part ^^). Slide on cover. Done.
The TP-Link Deco BE85 Skådis Mount is an easy print in two parts. You might want to add some brims around the lower hooks, and you will need supports for the upper hooks. It is a tight fit. Try to print the SizeTest first and adjust…
Used this to fix the internal air diverters in my BMW Z4 e85 dash that were broken and no longer adjustable, Replacing is pretty simple, follow youtube directions for how to slide the vents out (simple once you figure out how to release…
Using the bracket designed by DigitalSolo as a base, I snipped off the original mounting points and added some to fit in my Miata's engine bay (NA, LHD). This mounts on the side of the fuse box in the engine bay in place of the wiper…
Made wider and taller and added a support bridge on at the top of the bracket for added strength. Made the holes on the base to accomodate a 3mm knurled brass insert. Printed with 6 walls and 30% infill using PETG
Based on original model dimension foot of Jamo E850 (Jamo reference : 27094) You will additionally need one M8x6mm (10mm outside diameter) insert per foot. For example :…
This is Tripod Mount Adapter for the Flir Ex and Exx series. It straps to the handle with a piece of double sided velcro. This fits: E4 / E5 / E6 / E8 E53 / E75 / E85 / E95 E54 / E76 / E86 / E96 Step files attached.
Phone holder BMW Z4. The phone can be turned to horizontal and vertical position. The files are made for an iPhone 17 with a protective cover. No tools needed, can be removed anytime without leaving traces. The 3 parts are self…
BMW e46 window regulator started skipping I have designed repair part. In order to change it, you need to remove the door covers, and i will not explain this, there are hunderds of videos on YouTube for This. Print the Gear part with…
No supports needed. I printed the model in PLA (15% Infill).
This is a lens cap for the Flir Exx series handheld thermal imaging camera This cap should fit: E53 / E75 / E85 / E95 E54 / E76 / E86 / E96 Step files attached.
have also added one for 91 RON
This adapter allows for the use of Cokin A-Type filters within the LEE85 system. The filters push fit into the adapters quite snugly, however a tiny run of PVA down the strip works quite well, and is still removable. I have tested filters…
The Deco BE85 tp link HB810 runs quite hot due to the 10GbE Ethernet ports and the 6GHz wifi 7 chipsets, the original cooling capacity also isnt the best. Being WiFi 7 the range of the signal is also easily affected by height, this print…
This is a USB Cable Brace for the Flir Exx series handheld thermal imaging camera. Just like the Flie E series, there is a bit too much pressure applied to USBc cables when plugged in, so this reduces the pressure put on cables while the…
This is an updated holder for the Samsung Galaxy Z Flip 8 phone to be used with the "Samsung Galaxy Z Flip 5/6 Mount for BMW Z4 (E85/E86) found here. This is only the updated holder. The mount and bolt hardware will need to be downloaded…
Using the bracket designed by DigitalSolo as a base, I snipped off the original mounting points and added some to fit in my Miata's engine bay (NA, LHD). This mounts on the side of the fuse box in the engine bay in place of the wiper…
