123 modeli
UPDATE 09/2024 Add new version V8 for G93SC and G93SD with monitor clip. You can clip this version to your monitor without additional tape. Would be nice to get feedback for G95SC. Add new version V5 to fit G95SC. Description This is my…
I found a way to generate topographic maps from saetlite data, then used prusaslicer 2.7 to emboss a track map on it that matches the curves of the hills in the area. the result is a 3d printable topographic track map The finish Line is…
BUILD GUIDE INTRO Remember your promise in a most rootin' tootin' fashion 🤠 Presenting Sidetrack, a break-action hammer-prime revolver! Heavily remixed from the Hammerhead by Leedle Dynamics, the Sidetrack achieves higher performance and…
The spiral is modular . That means that there is a minimum set of required parts, and a few optional parts to increase the height, change the marble inlet, add stabilizer pillars etc. Marbles cannot fall out of the Spiral - no matter how…
Nurburgring Nordschleife, Nurburg, Germany, on a stand with it's name. Race track 3x3 mm Stand 198x3x15 mm Gap for putting the track into the stand 0.1x0.1 mm bigger so it's easier to assemble. Looks best when separate parts printed in…
I spent a long time looking for an elegant solution for the steep curves that isn't permanent. I found the safety fence and adapted it to the scale and my clips. I have modified my clips so that they can be used in steep bends. The fence…
You may need to heat up the camera mounts so you can bend it to make the camera fit easier. A little late to mention but the camera mounts fit my 160 FOV cameras, its a tight fit, I'm not sure of the compatibility with 130 FOV cameras.
Update 7.02.2023: Added Pre-Build Bridges and a Hexgon Plate. You can extend them with any other element using the top/bottom clips. This spacer (grid)element has several advantages. The Hexagon connector is very tight and holds firmly on…
Mount Panorama Circuit, Bathurst, Australia, on a stand with it's name. Race track 3x3 mm Stand 198x3x15 mm Gap for putting the track into the stand 0.1x0.1 mm bigger so it's easier to assemble. Looks best when separate parts printed in…
Fiber optic spool holder with racetrack to manage extra fiber. I used this to extend my ISP's fiber and couple it into extra fiber in my house. Has a spot for a panel mount coupler as well. Print it on the bottom face and let the back…
Laguna Seca Speedway, Monterey, USA, on a stand with it's name. Race track 3x3 mm Stand 198x3x15 mm Gap for putting the track into the stand 0.1x0.1 mm bigger so it's easier to assemble. Looks best when separate parts printed in different…
Daytona International Speedway, USA, on a stand with it's name. Race track 3x3 mm Stand 198x3x15 mm Gap for putting the track into the stand 0.1x0.1 mm bigger so it's easier to assemble. Looks best when separate parts printed in different…
Camera and LED mounts for the Quest 2 for use with the EyeTrackVR project to add eye tracking! Print in PETG for best results, PLA is fine. Both general/V3 LED and V4 LED mounts are included.
Ich habe mir hier ein ein Paar Untersetzer für Gläser oder Tassen mit Rennstrecken Konstruiert (Nürburgring Nordschleife, Zandvoort , Spa , RedBull Ring , Circuit de Catalunya , Le Mans , Imola , Monza) ------------------- I've designed a…
EDIT: I got a request for another racetrack, so I added WATKINS GLEN. I was thinking about re-decorating my apartment - spicing-up these old cupboards and lockers or some new pictures on the wall. As I am a huge motorsports fan it might…
Watkins Glen, Dix, United States, on a stand with it's name. Race track 3x3 mm Stand 198x3x15 mm Gap for putting the track into the stand 0.1x0.1 mm bigger so it's easier to assemble. Looks best when separate parts printed in different…
A simple DIY LED holder for head tracking, designed for 5mm LEDs. The first iteration (pictured) was designed with the option to mount LEDs on Dupont connectors so that they could be easily replaced. This, however, proved troublesome to…
*** Thanks for checking out this model! *** If you appreciate what I'm doing, consider buying me a coffee , and check out my other models for something else you might like! ********** I developed and tested the STRONG and EVEN STRONGER…
Sebring International Raceway, USA, on a stand with it's name. Race track 3x3 mm Stand 198x3x15 mm Gap for putting the track into the stand 0.1x0.1 mm bigger so it's easier to assemble. Looks best when separate parts printed in different…
Dimensions: 125x139mm Height: 5mm Thickness: 2mm Can be easily scaled up or down. Recommended print setting: Resolution 0.2 or lower Ironing on top surface 20% infill
3D model of the Imola race track One model is just the track, the second one is with the name of the track. width: 6mm height: 10mm
extrusion of nurburgring nordschleife
Road America Circuit ,Elkhart Lake, Wisconsin, USA, on a stand with it's name. Race track 3x3 mm Stand 198x3x15 mm Gap for putting the track into the stand 0.1x0.1 mm bigger so it's easier to assemble. Looks best when separate parts…
Road Atlanta, Braselton, United States, on a stand with it's name. Race track 3x3 mm Stand 198x3x15 mm Gap for putting the track into the stand 0.1x0.1 mm bigger so it's easier to assemble. Looks best when separate parts printed in…
Custom solution for a clean, unobtrusive, EyeTrackVR installation in the Valve Index . Project includes: Custom, highly iterated camera and LED mounts based on bitbyt3r's design. These revisions alone may be preferable to some. All-in-one…
Masarykův Okruh, Brno, Czech Republic, on a stand with it's name. Race track 3x3 mm Stand 198x3x15 mm Gap for putting the track into the stand 0.1x0.1 mm bigger so it's easier to assemble. Looks best when separate parts printed in…
Edited so the usb-c cable that powers it goes out straight instead of outwards. Also now has a window so you can have a heatsink on it.
This is a simple DIY freetrack/ trackIr headset. It is made to use an action cam battery, mine is 33x30 mm from a cheap action cam and 5mm ir leds. The battery connector was bought in aliexpress:…
Fuji International Speedway, Oyama, Japan, on a stand with it's name. Race track 3x3 mm Stand 198x3x15 mm Gap for putting the track into the stand 0.1x0.1 mm bigger so it's easier to assemble. Looks best when separate parts printed in…
Brands Hatch, Fawkham, United Kingdom, on a stand with it's name. Race track 3x3 mm Stand 198x3x15 mm Gap for putting the track into the stand 0.1x0.1 mm bigger so it's easier to assemble. Looks best when separate parts printed in…
3D model of the Monza race track One model is just the track, the second one is with the name of the track. width: 6mm height: 10mm
Podpěra pro zvýšení trati autodráhy. Kvůli snadnějšímu tisku je zvlášť na několik dílů. Není to na časté rozkládání, jeden prodlužovací kus se mi podařilo rozlomit, takže spíš složit a nechat být :-) Můj teprve druhý model. A support for…
This marble run is designed to use LEGO bricks as height supports, allowing you to customize and build intricate tracks. It accommodates standard 16mm diameter glass marbles, providing smooth and exciting runs. Enjoy endless fun and…
My setup: 3x5 mm IR transmitting LED Power supply voltage: 5 V LED voltage drop: 1.3 V LED current: 50 mA 22 Ohm resistor Assembly guide: Print a model Do some calculations. Using this LED array calculator I found that my setup requires a…
Tsukuba Circuit, Shimotsuma, Japan, on a stand with it's name. Race track 3x3 mm Stand 198x3x15 mm Gap for putting the track into the stand 0.1x0.1 mm bigger so it's easier to assemble. Looks best when separate parts printed in different…
Las Vegas Strip Circuit, Nevada, USA, on a stand with it's name. Looks best when separate parts printed in different color filament. If you appreciate my work please consider donating me on Ko-fi . If you have some requests for new…
Sonoma Raceway, Sears Point, United States, on a stand with it's name. Race track 3x3 mm Stand 198x3x15 mm Gap for putting the track into the stand 0.1x0.1 mm bigger so it's easier to assemble. Looks best when separate parts printed in…
6DOF headtracking clips to be used with FreeTrack, TrackHat or other similar headtracking systems. Inspired by http://www.thingiverse.com/thing:62827 . I created two versions of clips to keep the two halves of the arms together. One…
Introducing an excellent Sidetrack remix designed by @Avinashshank_1450204 to use round metric tube for the plunger tube! This makes the blaster much more accessible with minimal changes in hardware. To build this version of the Sidetrack…
Made a small 1x1 Gridfnity storage for my UGREEN FineTrack Smart Finder. Designed it so that i can find it the next time
Pista di Fiorano, Italy, on a stand with it's name. Race track 3x3 mm Stand 198x3x15 mm Gap for putting the track into the stand 0.1x0.1 mm bigger so it's easier to assemble. Looks best when separate parts printed in different color…
Goodwood Circuit, United Kingdom, on a stand with it's name. Race track 3x3 mm Stand 198x3x15 mm Gap for putting the track into the stand 0.1x0.1 mm bigger so it's easier to assemble. Looks best when separate parts printed in different…
Long Beach Street Circuit, USA on a stand with it's name. Race track 3x3 mm Stand 198x3x15 mm Gap for putting the track into the stand 0.1x0.1 mm bigger so it's easier to assemble. Looks best when separate parts printed in different color…
Includes 2 versions - Barcelona or Barcelona-Catalunya Dimensions: 202x70 mm Height: 5mm Thickness: 2mm Can be easily scaled up or down. Recommended print setting: Resolution 0.2 or lower Ironing on top surface 20% infill
Saw lots of single versions of wall mount race track connectors and thought there needs to be a double. So I whipped one up. This is done in PETG, 100% infill at .3mm layer hieght using a .6 nozzle. Speed at 35mm/s. Nozzle at 245 degrees…
Circuito Ascari, Málaga, Spain, on a stand with it's name. Race track 3x3 mm Stand 198x3x15 mm Gap for putting the track into the stand 0.1x0.1 mm bigger so it's easier to assemble. Looks best when separate parts printed in different…
Phillip Island Circuit, Victoria, Australia, on a stand with it's name. Looks best when separate parts printed in different color filament. If you appreciate my work please consider donating me on Ko-fi . If you have some requests for new…
3D model of the Monaco racetrack One model is just the track, the second one is with the name of the track. width: 6mm height: 10mm
Twin Ring Motegi, Japan, on a stand with it's name. Race track 3x3 mm Stand 198x3x15 mm Gap for putting the track into the stand 0.1x0.1 mm bigger so it's easier to assemble. Looks best when separate parts printed in different color…
This Mount is meant to be Printed 4 times and can be clipped to the top of a MSI Optix MAG274QRF-QD screen. The two cable files can be printed once each and are used to stop the cable from pulling the tracker out the Top.
Thunderhill Raceway Park, Willows, USA, on a stand with it's name. Race track 3x3 mm Stand 198x3x15 mm Gap for putting the track into the stand 0.1x0.1 mm bigger so it's easier to assemble. Looks best when separate parts printed in…
Wall Art,Nürburgring Nordschleife Racetrack Die Grüne hölle
Immerse yourself in the thrilling world of MotoGP with my exclusive Wall Art that represents the circuits of the 2024 MotoGP season. This collection features detailed representations of the most iconic circuits from the MotoGP calendar,…
3D model of the Misano racetrack One model is just the track, the second one is with the name of the track. width: 6mm height: 10mm
General These replacement parts are for the CubicFun hahaland Race Track Adventure Toy pictured above. My kids love this thing but it gets a lot of abuse between my 3 toddlers so I've modeled replacement parts as they've gotten broken.…
I have designed the objec customizable. I can change imediatly for a bigger 8 or a steel balls of a different size. The steel ball can only be insertet (or fall out) in the center!
Made with 12mm c/c holes for mounting. Holes are 5mm ID and fits standard pegboard fasteners.
3D model of the Mugello race track One model is just the track, the second one is with the name of the track. width: 6mm height: 10mm
Snetterton, Norwich, Norfolk, United Kingdom, on a stand with it's name. Race track 3x3 mm Stand 198x3x15 mm Gap for putting the track into the stand 0.1x0.1 mm bigger so it's easier to assemble. Looks best when separate parts printed in…
Printed in two parts and then glued together with two component glue. STL only left side model. Made in Blender 3.2 with CAD sketcher: https://makertales.gumroad.com/l/CADsketcher
3D model of the Suzuka race track One model is just the track, the second one is with the name of the track. width: 6mm height: 10mm
This is a specially designed face tracker that uses an ESP32-CAM module and requires no glue or modifications to the headset itself. It only needs a single M3 screw as a swivel point. The mount simply clicks into place and does not block…
Autodromo dell'Umbria, Italy, on a stand with it's name. Race track 3x3 mm Stand 198x3x15 mm Gap for putting the track into the stand 0.1x0.1 mm bigger so it's easier to assemble. Looks best when separate parts printed in different color…
Even with some PCARs, there is no exposed orange muzzle on the Sidetrack due to how short of a barrel is needed. I made this part to fit on the end of the long barrel variant so that it has some orange on the end for safety reasons (makes…
This alternate Cylinder allows you to flick the blaster closed! It also has better overall retention in the blaster, so it's less likely to go flying 😁 For printing and assembly, follow the same instructions from the original Sidetrack.…
Muzzle for Sidetrack inspired by Ace of spades hand cannon from Destiny. Print the Muzzle and shroud on the face vertically (as shown below). Use brims where necessary. Uses the same hardware as side track with an additional two m3x5 or…
A replacement for the barrel section of the sidetrack, needs some 4mm or 5/32" elastic cord to run. Check the steps or the pictures for assembly, it is really really simple. I cut it out of the regular frame for the photo because i dont…
bracket for tobii eyetracker 5 use with the extra magnet. this is to mount to a screen bracket from a sim racing screen
A face tracker mounting clip with an attached mount for a full body tracking system called Fluxpose
Print with support, with the axis of the round hole as Z axis. PETG is advised.
Separate to left and right eye mount for ease of uploading to online 3D printing services.
Link to toy: https://www.amazon.com/Palotix-Dinosaur-170PCS-Christmas-Birthday/dp/B08HZ6W83X/ There are many similar versions on amazon, but they should all fit. Just heat up the axle with a lighter to ensure a tight fit and put a dab of…
wanted to use this model for a wall of bookshelf + hotwheels display for a kindergartener
Enclosure for Ugreen Finetrack G (Rechargable) mounted under a bottlecage Ideally printed in ASA Filament for UV resistance (ASA > PET > PETG > Everything else) This requires a longer M5 x 25mm bolt to be mounted properly Additonal Tip:…
I designed this test print in order to check input shaping and accelerations with Klipper Tuning Tower command. Also have fun watching your printer running around this famous circuit. UPDATE 23/08/2023 ADD VERSION WITH 5MM MARKS IN ORDER…
3D model of the Jeddah race track One model is just the track, the second one is with the name of the track. width: 6mm height: 10mm
Build your marbletrack by yourselve! Several parts to have fun with marbles. Build your track with this parts and Lego or similar bricks. The marbletrack is for marbles from 5-10mm. The curved parts are all in clockwise direction. If you…
3D model of the Zandvoort race track One model is just the track, the second one is with the name of the track. width: 6mm height: 10mm
3D model of the Miami racetrack One model is just the track, the second one is with the name of the track. width: 6mm height: 10mm
Made for those wall arts in frames. An example of use is shown in the last picture, that is NOT mine. Made, by creating an SVG and then extruding it.
Quest 3 eye tracker compatible with VR Optiker prescription lenses. It clicks into the headset without tools, and the lenses snap securely into the adapter.
This is to mount a babble or similar facetracker on a steam frame, with an optional mounting lug for a vive tracker to slide on with a small detent and magnets help retain it on the slider pad. It also includes compatibility with the…
3D model of the Bahrain race track One model is just the track, the second one is with the name of the track. width: 6mm height: 10mm
A time tracker for D100 Dungeon to save the printed one from wearing out so fast, and this also saves me a few seconds each turn. I use two pegs to track time, like on a cribbage board, so I don't lose track of my current position as I…
The Curbs are made for cable duct in size 30x15 mm. You have to drill a 10mm hole in the cable duct, to hold it in place.
Shoutout to the haters. short and long versions
Albert Park Racetrack in the heart of Melbourne Australia.
This is a cap style point model for use with OpenTrack, FreeTrack, or FaceTrackNoIR. It is designed for external power, either via USB or a battery pack. Check out the Serial Build guide on the FreeTrack forums here:…
The Autódromo José Carlos Pace (Interlagos Circuit) , located in the southern zone of São Paulo, is the main motorsport circuit in Latin America and the venue of the São Paulo Formula 1 Grand Prix. Inaugurated in 1940, the current layout…
The new iteration, “PipKey”, is here: https://www.printables.com/model/995672-pipkey-bluetooth-midi-instrument A magnetic-themed, MIDI-based instrument inspired by the cello and designed to be portable, intuitive, and tactile. (The name…
3D model of the Albert Park race track One model is just the track, the second one is with the name of the track. width: 6mm height: 10mm
3D model of the Shanghai racetrack One model is just the track, the second one is with the name of the track. width: 6mm height: 10mm
FreeTrack is an open source software application that provides cost effective optical head tracking for applications & games. This software closely emulates its commercial counterpart, TrackIR. The headtracking is achieved by attaching…
I was commissioned to make this model for PGP Motorsports park and 3D-print a few hundred as promotional giveaways. Print in PETG or TPU to make a reasonably robust keychain trinket. I do not recommend ABS or PLA as they are too stiff
To replace a broken button.
Accessory plate to hold a UGREEN FineTrack tracking tag onto your Ridge Wallet. ***This design allows you to reuse the original plate screws!*** Just unscrew the screws from the face plate, lay the tracker plate onto the original plate,…
Introduction The racetrack tuner is a capacitive coupler for short transmitting loop antennas. The name is refering to its racetrack form. Racetrack Circus Maximus in Rome - maybe I should call it ’Maximus Tuner’ :-) For use by certified…
Ich bin im Seifenkistenverband Baden-württemberg e. V. aktiv. Hier haben wir eine Rennklasse, die nennen wir Mini Seifenkisten Racer. Kurz: MiniSKR. Dazu gibt es auch eine Internetseite: www.miniskr.de www.seifenkistenverband-bw.de In den…
![#0161 STRONG #8 Racetrack Double Split Key Ring [3 sizes] - Meets the Demands of Everyday Use!](https://media.printables.com/media/prints/882189/images/6978605_0d7baa1d-6198-4119-97c0-24ae7e11ad5c_795317cf-4c65-4771-8c57-787a2aa39eab/20240615_162825.jpg)
