Rugged GMR2 Rivian Mount
This is a single piece, use supports.
Wydruk około 5,70 €–6,97 € nettoWstępna wycena jednego wariantu
- Pobrania
- 31
- Polubienia
- 7
- Ocena
- 0
20 modeli
This is a single piece, use supports.
Wydruk około 5,70 €–6,97 € nettoWstępna wycena jednego wariantu
This is a scale model of a sggmrss container car. Included are fitting Y25 bogies. The bogies and waggon parts connect together via clips. The frame has holes for either piko containers or pins can be glued in for other containers. The…
This stand for the Btech GRMS Pro radio can be used when charging the radio, also as a table top holder when listening to the radio. The belt clip attaches to the back of the holder. No supports are needed and any filament should work…
I made this for my 2016 Jeep Wrangler, to hold my aux switches and as a good place to put my GMRS radio. It fits the profile of the trim piece above the windshield, with a cutout for the speaker on the bottom. The radio is a Midland…
This GMRS antenna is constructed using a 3d printed form and easy to acquire material from a hardware store. The antenna has better than 11 dBi gain in the forward and rear directions and will aid your handheld GMRS radio with an external…
Utilizes RAM Mounts Track Ball with T-Bolt Attachment RAP-B-354U-TRA1
This is a stand for the BTech GMRS Pro Handheld Radio. This was a quick build, I'll make a new, better version soon. Open in the back so that you can place or remove it from the stand with the charging cable still attached.
This headband can replace the filmy headband that is used in the Koss GMR-54x-ISO headset. for the Blank HeadBand, supports are needed under the band inside of the half-circle. On the second one supports should not be needed. 3 walls…
Mobile mount for Raddioddity GM-30 Plus GMRS radio. This is designed to be used with a Bullet Mounting system but it can be adapted to any mounting system. There is a ¼-20 size hole in the back to place a screw to attach the holder. I…
A very simple GMRS mount for your roof rack. I have a Midland MXT275 radio with Ghost Antenna on a Victory 4x4 Roof Rack.
Print two of thiese clips and slid them over the existing headband zip tie them on and stop them from breaking. Printed with no supports but bridging enabled. 15 % infill.
Printed out of ASA with 35% infill. Supports required. Fits this midland low profile cable.…
A friend of mine was welding on the bracket for the radio mount in his Jeep and melted one of the mounts and set for to the other. So I took the melted one and scanned it in and printed a new set for him. This is the bracket and mounts in…
I make replacement for my broken headphones Koss GMR 545 Air. Print it with PETG.
I designed this model after my GMRS magnetic antenna cable kept getting crushed by my car door, even when I routed it through the softest locations. Specs: Designed to fit 0.20” Dia. coax, but can be scaled to fit whatever size you need…
The soft “rubber duck” antenna shells on my marine Uniden walkie talkies crapped the bed (too old, broke apart). This shell replaces them. I used Ninjaflex, but any TPU can do the job.
I made this cover for my GMRS Radio so there is no gap. used TPU 100% infill here is the link for the antenna used for this model https://a.co/d/dsEo7fo Enjoy
easy to print and click on repair. if you adapt the size with test prints you can do it without the tape (like i did) you need the to print the "Koss_GMR545-air_Repair" 2x times. i also added the fusion archive and step file if you want…
This is a radio clip mount for a BTECH GMRS-PRO. I took an existing design and modified it to work with this radio. Remixed from "Baofeng UV-5RA Mount" by turbo2ltr ( https://www.thingiverse.com/thing:756744 ), licensed CC BY-SA. You will…