Wyniki wyszukiwania: jo

DUMMY 13 Printable Jointed Figure (BETA FILES)

HUGE UPDATE 9/13/2024: Dummy 13 v1.0 is now available! Check out the new and improved version of Dummy 13 here. This page will keep the previous beta files to ensure that no one's remixes are broken. Dummy 13 uses a CC BY 4.0 license!…

LUCKY 13 Printable Jointed Figure

Lucky 13 is now on a CC BY 4.0 license! This means that you are free to share these files however you like, including selling prints, provided that you give proper attribution. You can give proper attribution by including this notice on…

CARBON 13 Printable Jointed Figure - Type M - Beta files

About this model Say hello to Carbon 13, the latest generation of 3D printable action figures. Carbon 13 introduces a hybrid joint system that preserves the dynamic range of articulation you expect from the 13 series while freeing up…

Joycon Controller with Trigger buttons. Easy print

Hi everyone, the Controller is designed to be printed standing up without supports. There is a bit of postprocessing required to remove the custom supports for the Trigger button flexure. Enjoy printing

EASY 13 Printable Jointed Figure

Easy 13 is now on a CC BY 4.0 license! This means that you are free to share these files however you like, including selling prints, provided that you give proper attribution. You can give proper attribution by including this notice on…

#3DBenchy – The jolly 3D printing torture-test by creativetools.se

As of February 14, 2025, the 3DBenchy model has been released into the public domain. For more details, please visit the link below: https://www.3dbenchy.com/3dbenchy-sets-sail-into-the-public-domain/ #3DBenchy is a 3D model designed by…

CARBON 13 Printable Jointed Figure - Type F - Beta files

About this model Say hello to Carbon 13, the latest generation of 3D printable action figures. Carbon 13 introduces a hybrid joint system that preserves the dynamic range of articulation you expect from the 13 series while freeing up…

Josef Prusa's pug Buddy

Author: Jindrich Benes (Prusa3D) https://www.prusaprinters.org/social/12/prints Josef Prusa's very own pug, Buddy. Bundled with every Original Prusa i3 MK2S & MK3. Print in black. Print instructions Print takes roughly 1 hour and 30…

Gyro 7 Printable Jointed Cat

The orange Gyro 7 in the pictures is printed in 0.20mm layer height Printing Material: PETG (PLA makes the joints too loose when using the normal skeleton and too tight for the tight Skeleton . Assembly is also more difficult in PLA.)…

Chicken Jockey : Minecraft the Movie

Chicken Jockey :Minecraft the Movie Updated with Base: Needed it. Added details to back. fixed face of zombie child. Thickend chicken feet.. (4/12/25) Left the old version of chickenjocky up as another .obj. (no base)

Joycon Grip with Front-Looking LED Windows

A Nintendo Joycon grip with front-looking windows for the LEDs. It prints without supports and the LED windows face forward, so you can see them right as you normally hold the joycon. The LEDs shine into a slit that arrives to a 45º…

🗲 Full-Size Mjolnir 3-piece screw together (Thor's Hammer) 🗲

PLEASE UPDATE YOUR FILES to ensure the best fit. ( updated 1/10/23 ) Stronger Handle and simpler labeling for less mistakes. 49 hours too much? Try 60% version→…

Joy Fidget

This fidget toy is a joystick toy applied ball joints. It is designed to be operated smoothly and unconsciously with one hand. You can adjust the tightness by tightening the screws. Print settings: Material: PLA, PETG Layer height: 0.20mm…

Nativity Joseph

Nativity Joseph.

Nintendo Switch Joycon Shells

When trying to repair joy-cons I as do many people, striped one or more Y-screws and had to damage the shell remove the screw and repair the joy-con. So I needed a new shell but why buy something small and made of plastic when you have a…

🗲 Thor's Hammer Mjolnir 2-piece screw together 60% scale 🗲

Shout out to 80sNerdBomb for the model. The Vertical version is much better . Thread support works well and comes out easily. Images in makes. I printed it in Prusament My Silverness PLA and Mystic Brown PLA.

D&D Tokens -Simple JoCat Style for Classes

Inspired by an old set of tokens I had found on this site. https://www.thingiverse.com/thing:2591952 Made in the same syle as my other tokens and using the JoCat icons for the classes. Easy to print tokens for when you can't find just the…

Little Josef Prusa Character - Multi Material

Author: Dominik Cisar https://www.prusaprinters.org/social/7/prints The Man. The myth. The legend. Little Josef Prusa Character, designed at the occasion of the Original Prusa MULTI MATERIAL UPGRADE 2.0 release. The model consists of…

Josef Prusa's pug Buddy 2.0

A sculpture of one of our long-time mascots, Josef Prusa's pug dog named Buddy. There is a single-tool version, a dual-head version (with painted eyes, toenails, and collar), and two versions for the five-head XL: one with three colors…

Articulated Jellyfish with ball-joint tentacles

I recently had someone request that I make them a Jellyfish. I found a nice articulated model on Thingiverse but it had some issues with the .stl files and also required glue. I decided to re-mix this model and eliminate the need for…

Vallejo, Army Painter, Reaper Paint and Brush Holder

Paint bottle holder designed to fit Vallejo, The Army Painter, and Reaper MSP paints. Each brush or tool slot has a cutout for easy cleaning if things get messy inside; it also helps fit The Army Painter triangular brushes. This model has…

34 Small Christmas cookie cutters / 34 Vánoční vykrajovátka / Ausstechformen für Weihnachten

🇬🇧 – English – A collection of 34 Christmas cookie cutters. Small ones, usually between 3.5 - 5 centimeters big. Collection includes: angel bell candle candy church comet cookie cross fish glove hat heart house moon mug ornament pig…

Air Jordan VI - Pot Plant

Any feedback would be greatly appreciated . Could be use as a planter, pen holder, etc Nozzle: 0.4-0.8mm Layer: 0.24-0.4 (Recommended) Supports needed Scale it as you like :)

Rangement / organisateur pour peinture maquette army painter, vallejo

Organisateur de fiole de peinture à maquette, (pour fiole army painter, vallejo,...) -40 emplacements fiole peinture + 9 emplacements pour pinceaux -24 emplacements fiole peinture + 5 emplacements pour pinceaux

Requiem Arrow( Jojo's Bizarre Adventure )

This is the requiem arrow from Jojo's Bizarre Adventure Part 5: Golden Wind used by Giorno Giovanna

mini cute Thor Hammer (Mjolnir)

This is a mini cute version of Thor Hammer (Mjolnir). It fit in 4.5 x 3 x 9 cm. No support needed. If the scale fit your needs, use the gcode file, I selected lightning pattern to get a faster print. It can be upscaled easily to life size…

Skadis / Skådis - miniature paint holder (Vallejo / Citadel / Pro Acryl)

Paint holder for mini paints for the Skadis / Skådis system, three versions that fit either vallejo (or others of the same size), citadel or pro acryl. The dropper bottles (vallejo and pro acryl) fit either standing normally, or upside…

John Wick Blood Oath Marker

John Wick Blood Oath Marker I plan on doing this again. I am not satisfied with it. I am going to approach it with a different design technique in the near future.

Generic ball joints for camera mounts and other adjustments

For the articulated arm that holds the RaspberryPi camera on my Prusa Mini, I needed a way to fine adjust the viewing angle of the camera. So I opted to design a ball joint. I did a number of prototypes to try out how much the socket…

guitar/banjo/autoharp finger and thumb picks

Almost out of filament? Print these with the last few fractions of a meter, and in a just a few minutes you can sing the blues. You can also load up a new spool set up a new print, and Rock ON while the new prints proceed! These couple of…

Geodesic Greenhouse - Articulating PVC Joints

Introduction This is a concept for greenhouse based upon a geodesic dome using 3D printed articulated joints, PVC pipes, and greenhouse plastic. Unfortunately I don't have the funds at the moment to realize the full concept but the 3D…

Modified Nintendo Switch Joy-con grip (remixed)

Credits to manabun on Thingiverse for the great original design! Original: https://www.thingiverse.com/thing:2769344 I modded the design to be printable in a better position without support. The slot is slightly modified for an easier fit…

Papageno's Bird Call from The Magic Flute (5-note flute in G Major or F Major)

Update June 18 2023: I moved the lanyard lugs to the sides, which should make the bird call dangle better when worn as a necklace. This is a set of whistles tuned to the first five notes of a G or F Major scale. It is designed for use as…

Your custom 17ml paint bottles stand (Vallejo, Army painter, Green Stuff World and etc)

The design is my own. Its easy to print, with no supports. If you need feel free to glue parts together. Default file are 7x5 bottles (maximum Prusa i3 print bed) and 20 degree stand. If you wanna change number of bottles or degree of…

Air Jordan I - Pot Plant

Any feedback would be greatly appreciated . Could be use as a planter, pen holder, etc Nozzle: 0.4-0.8mm Layer: 0.24-0.4 (Recommended) Supports needed Scale it as you like :)

Spring INJORA BZ-04BR

Here is a link to the shock absorbers for which this replacement part was designed. https://vi.aliexpress.com/item/1005004599082114.html?spm=a2g0o.order_detail.order_detail_item.7.1b34f19cOyW5Rm&gatewayAdapt=glo2vnm printing: perimeter -…

Little Josef Prusa Character - SINGLE COLOR

Action figure of Josef Prusa

Spherical flexure joints "Tetra 1" - no supports required. Remix, as seen on The Action Lab

Recommended print settings: Material: PETG Layer Height: 0.20 Infill % : 15 Supports: No Print Orientation: Default as modeled. As seen on Jelle Romers video: And article:…

Prison Realm Satoru Gojo - Jujutsu Kaisen Figures

Any feedback would be greatly appreciated . Nozzle: 0.4mm Layer: 0.1-0.2mm (Recommended) Add a some small Cylinders as Negative Volume for draining No Supports needed Scale it as you like :)

ADJUDICATOR COIN : John Wick

ADJUDICATOR COIN

Honest John Missile / Rocket

This is a flying model of the Honest John missile / rocket used in the Vietnam era. The model fly's on E and F rocket motors or just build as a static display model. The model is comprised of 3D printed parts, two Pringles tubes and a…

Mighty Journeys in Middle-Earth Organizer

It stores all contents of the Journeys in Middle-Earth game in the core box and its two expansion boxes. The core box holds all the minatures, the battle field maps and the rules. One expansion box contains all the cards and tokens and…

Dwayne "The Rock" John 117

Now we finally know what Master Chief looks like under that helmet. Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: No Supports: Yes Resolution: 0.1mm Infill: 10% Filament: Polymaker PLA Matte Grey

Vallejo paint bottle storage Tray

A storage Tray designed to hold x32 vallejo model Air bottles 17ml (0.57 fl oz), each storage location is a friction-fit, ensuring the bottles are held tight and securely. There are two designs one with the brand name Vallejo and a second…

Skadis Vallejo 50mm Bottles 200ml Holder

This is for Ikea Skadis to organize even the bigger Bottles like the 200ml (Thinner,Cleaner, e.g.) As I was searching for such Holder and didn't find any, I created some. Now I have all Types clean at the wall mounted ready for picking…

John Deere cookie cutter

K dispozici jsou 2 vykrajovátka na cukroví - s jelenem a bez jelena. Pokud chcete dělat cukroví jako na obrázku (linecké), udělejte jedno bez jelena, potřete ho marmeládou a přilepte k dílu s jelenem.

YoYo (JoJo)

Print the Yoyo with 80% infill and the yoyo will weigh about 60grams. The screw and the 3mm middle-nut should be printed with 100% infill for strength. The nut should obviously be in the middle of the screw. The screw could break if you…

Skyjo travel case

Update (04/02/2024): I've added a base design that has a space for the score booklet, it is 7mm thicker than the original design. Simple print, 15% infill, no support. I'm holding it close with a rubber band when traveling. On the base…

Dwayne "the Vase" Johnson aka The Rock

No reason at all. None. I picked the egg because it had a nice chin & nostrils for vase mode.

VIVE Facial Tracker Mount for Varjo Aero

Tested to work nicely on Varjo Aero headset. Don't use PLA as it will make the mounting fingers too fragile. Printed in vertical orientation with generous supports. Update about XR-3: This occludes the LiDAR in the center and can leave a…

Joseph Stalin (Иосиф Виссарионович Сталин)

Joseph Stalin. Bust.

Vase with Winged Griffins by Prosper Jouneau

Vase with Winged Griffins by Prosper Jouneau

Mannequin with Print in Place Joints

This is a study on print-in-place articulation. I wanted a small anatomical figure that was jointed. I found other great designs where you print the respective parts then assemble, but scaling down caused difficulties as the smaller snap…

TARS Robot: Magnetic Joints

This is my model of TARS from the movie Interstellar. TARS body consist of 4 legs, this model uses magnets to form joints and keep everything together. The magnetic joints slides along the full leg length which makes for a very flexible…

John Wick silhouette

John Wick silhouette intented to be fitted in a photo frame. Fits on a Prusa Mini+ bed. Gcode file included with a (very) long ironing process for the top surface.

Double Dropper Bottle Paint (Vallejo, Army Painter, etc.) Holder for Pegboard

A simple holder for dropper paint bottles, such as used by Vallejo, The Army Painter, and similar. It is designed to hold nine bottles, and secured to a standard pegboard that can accept 6mm pegs. This is remixed from an earlier design on…

Josy the French Bulldog

I designed this model based on my own French Bulldog named Josefine Rose, a.k.a. Josy :) Designed on Nomad Sculpt, this model prints without supports, but a brim is advised. Shes a sweet girl with black fur and big brown eyes, who is…

Journeys in Middle-Earth: Shadowed Paths terrain

Component replacement for Lord of the Rings: Journeys in Middle-Earth: Shadowed Paths expansion. File names say how many copies are needed for each. Nest Web and Nest Base are glued together afterwards. I added some webbing on the eggs…

Porche 911 from glenjohnston on thingiverse: split and optimized

Optimized version of https://www.thingiverse.com/thing:39105 Different parts split in different bodies Bottom of car body flattened Rescaled, and multi-layer height optmization in the print files. Copyright 2014 GlenJohnston

Comical and Edgy Bad Parking Job Award/Handout - Business Card/Wallet Size For Easy Placement (zip tie holes for fun)

Joint Connectors for 12mm Tubes in JYSK Wardrobe / Verbinder für 12 mm Rohre

Bought a cheap wardrobe (too cheap, may be) which collapsed after moving too much stuff into it. These connectors were used to repair it. The small cylinder is only if you have the need to reinforce one of the tubes if it is folded.…

C920 Ball Joint Mount for Articulating Camera Mount for Prusa MK3 and MK2

This is ball mount joint for a Logitech C920 camera that allows it to directly attach to the ball nut from the Articulating Raspberry Pi Camera Mount for Prusa MK3 and MK2. This allows you to remove the standard mount from the C920 and…

Remix-A-Stix: A Remixable Parametric Joint System

Remix-A-Stix are a set of parametric ball joints, sockets, and connectors, compatible with Mini 13/Lucky 13 ball joints (via 6mm ball joints) and Gunpla accessories (via 3mm pegs & holes). Dimensions and tolerances can be remixed using…

Iggy from JoJo's Bizzare Adventure

Just finished season two of JoJo's bizzare adventure. Loved Iggy, he is favourite mutt! So I made a sculpture of him you can print. :)

Heart toast cutters / Vykrajovátka na srdíčkové tousty

[EN] Set of heart-shaped cut-outs for making heart-shaped one-dish cakes. PLA is fully sufficient for printing. For hygiene reasons, it would be preferable to always use a new set, however, in case of repeated use, cleaning in the…

Jolteon

Student 3D designer chasing a dream. I don't own a printer yet, but every like and download truly helps. Thank you! All❤

Vykrajovátko na perníčky ve tvaru vločky / gingerbread cutter in the shape of a snowflake

It's just a gingerbread cutter.

Joycon Controller with Trigger buttons Fuzzy Skin Modifier

Modifier File to add fuzzy skin to the handles only. Not perfect but works quite well. The world coordinates for the modifier are X: 0, Y: 4.30 and Z: 8.39. Takes some time getting it into the right place so make sure it looks like the…

Nintendo Joycon Storage for Transport with Case Lid

Visible on the photos, the wrist wrap does get in the way to fully close. This fixes this. Sadly made no new pictures.

Banjolin (Banjo Mandolin)

As an luthier & printer, I believe the banjo is a perfect instrument for printing since the component that has the biggest effect on tone (the drumhead) is a standard component purchasable at any music store. Printing can even improve on…

Logitech G915/815/ Apple Magic Keyboard 1 2 vertical keyboard stand with joined parts

Simple remix with joined parts of https://www.printables.com/model/73423-logitech-g915815-vertical-keyboard-stand Update 11/11: I also recently purchased an Apple Magic Keyboard 2, the fit isn't perfect but it works well

Johnny West Action Figure Revolver

The .gcode is already cut in half and placed in the most optimal print position. The .stl and .step are left whole in case you want to use them elsewhere. Happy Printing!

Vallejo paint rack for Ikea Skådis

Made for use with two (2) Universal Hooks from : https://www.thingiverse.com/thing:2853257/files Huge thanks to CSD_Salzburg for the hook design. I wanted something to keep my paints upside down, so this is what I came up with.

Glitter Gel pen adapter Cricut JOY to Maker 3

Hello, I propose a clamp for the GLITTER GEL CRICUT JOY pen to be mounted on your CRICUT MAKER 3. To be printed without support with a raft. Good print !

Makita DPJ180 Plate Joiner Flachdübelfräse Lamello Box

Printed in two halves, because of the large size. No support needed. Connected by 2.5x8mm cylindrical pins and/or glue. There is a small gap when the box is closed. To make sure no parts escape from the organizer when the box gets tilted,…

Funnel for vallejo bottles

Funnel for pouring paint into vallejo bottles. Fast print, helps speed up the process and make less mess.

Oil Barrel Jonh Deere

Este barril es un excelente adorno para tu escritorio, es el logo de la empresa John Deere. Se imprime sin soportes.

Jo Jos bazar Adventure Sex Pistols.

Jo Jos bazar adventure Sex Pistols. They ride bullets to help guide them.

Dwane “The Rinker” Johnson ready to print+gcode

the rock “thinker" w/ .gcode

Benchtop Jointer Dust Port Adapter

Acquired a benchtop jointer second hand, but it was missing the dust port adapter. This works with the Delta 6" Variable Speed Bench Jointer as shown, and possibly works with the following as they all look like they are made in the same…

FieldMark – Field Journal Stencil

Overview RangeVault FieldMark Field Journal Stencil Mark the Moment. Plan the Next. If you carry a field journal and actually use it—at work, in the shop, or out in the world—FieldMark helps keep notes clear, consistent, and easy to…

Serre-joint dormant

Serre-joint dormant pour serrage de grandes pièces et montages, des panneaux, etc. Les tests donnent un serrage de plus de 75 Kg sans problème, ce qui est suffisant pour bien coller s'il n'y a pas besoin de contraindre le bois. Pour des…

JOHANN STRAUSS II

JOHANN STRAUSS II

Stranger things shelf for 12 Kinder Joy figures

Hello, Today I have a Stranger Things shelf for 12 Kinder Joy figures for you. The shelf is designed to display figures from Kinder JOY eggs. It is designed for 12 of these figures. If you have more, you can put them on top :-) Happy…

30 Christmas cookie cutters in 3 sizes | 30 Vánočních vykrajovátek ve 3 velikostech

A collection of 30 Christmas cookie cutters. All models are in three sizes - 3.5, 5.5 and 7.5 centimetres. Collection includes: angel bell fish heart santa skate snow glove snowman tree wreath – Czech – Kolekce 30 vykrajovátek na vánoční…

30 Christmas cookie cutters in 3 sizes | 30 Vánočních vykrajovátek ve 3 velikostech

A collection of 30 Christmas cookie cutters. All models are in three sizes - 3.5, 5.5 and 7.5 centimetres. Collection includes: candle candy church comet glove heart pig present snowman sock – Czech – Kolekce 30 vykrajovátek na vánoční…

Joe Burrow ( Burr-OH ) w/ OHIO State Outline Bengals QB

Joe Burrow is one of the rising stars in the NFL after bringing his team burr-oh so close to a Super Bowl victory during the 2021 NFL season. I made this plate as a way for all Cincinnati Bengals and Joe Burrow fans to display their pride…

John McClane - Die Hard funko POP!

Print & acrylic draw

30 Christmas cookie cutters in 3 sizes | 30 Vánočních vykrajovátek ve 3 velikostech

A collection of 30 Christmas cookie cutters. All models are in three sizes - 3.5, 5.5 and 7.5 centimetres. Collection includes: angel bell cookie hat moon ornament snowflake star tree wreath – Czech – Kolekce 30 vykrajovátek na vánoční…

XAC joysticks and universal adapter

Hi guys! Well, clearly I should have uploaded this design a long time ago , but you know how it is, you chase time, then it passes, then you forget... But the controller contest made me think about it again and I hope it will be useful to…

Joints for cover of elevated bed (greenhouse)

1 central 4 left 4 right sticks folie

gridfinity 1x2 cardan joint and reduction step bin sae

Gridfinity 1x2 bin for holding a sae 1/2" cardan joint and a 3/8" reduction step socket Here's a gridfinity bin size 1x2, where you You can stash a 1/2" cardan joint and a ½" to 3/8 reduction step socket. Used with 1/2" drive ratchet.…

double-breasted dovetail joint partially embedded - oboustrabbý rybinový svlak částečně zapuštěný

Double-breasted dovetail joint partially embedded, teaching aid for joiner and carpentry in secondary schools. Oboustrabbý rybinový svlak částečně zapuštěný, výuková pomůcka pro obory truhlář a tesař středních škol.

Vallejo 16x organiser

Vallejo paint bottle organiser for 16 bottles. Inner diameter is 25mm, it is friction fitted. I just put the least used paints in the middle. Printed in PLA. Enjoy :)

Essential Bullet Journal Stencil

Checkbox For checklists and task-lists. Draw a line through it to indicate you've moved an item to another list. Draw an X in it to indicate you've canceled it. A Checkmark indicates that it is complete. Schedule A specific to-do item to…

Printables By Joseph Prusa Logo

This is my humble contribution to the rebranding of PrusaPrinters.org to Printables.com. Thank you Prusa for this amazing community. For 0.2 layer high change filament at 2.2mm and 3.2mm or use the built in function to apply color change…

Vase #10 - Basalt Columnar Joints

This model of a vase is inspired by the stunning basalt columns at the Giant's Causeway in Northern Ireland. The model can be combined with a glass insert to make it waterproof. The glass insert can be easily removed for easy cleaning.…

Weel adapter for John Deere Peg Perego

PET-G 6 kontures 85% infill from 30mm to 45 mm 100% infill PET-G 6 Konturen 85% Füllung ab 30 mm bis 45 mm 100% Füllung

Mobile Phone Clamp for Joby GorillaPod Tripod

This is a modification of Stamos's remix of the Tripod Mobile Phone Clamp. A base plate for GorillaPods was added.

Mjolnir & Stormbreaker Display

Mjolnir & Stormbreaker displayed on a base.