Wyniki wyszukiwania: prado

Toyota Prado Air Vent Knob

I printed in PETG on its side using tree supports for the arms.

GME MB206/MB207 Contoured Backing for Toyota LandCruiser Prado 150

GME MB206/MB207 backing plate contoured to the dash trim in the Toyota LandCruiser Prado 150 for easy mounting. Both left and right side trim variant .stl files are provided, use the correct one for the side you wish to attach the mount…

Toyota Prado Electric seat drive gear

Replacement nylon electric front seat gear for Toyota Land Cruiser, Prado, Toyota Granvia, Toyota Regius Printed in Taulman bridge nylon 2 Variants V1 15mm ID smooth bore V2 approx 14mm ID with splines

Vent tab for Toyota Prado

Mine was broken and apparently, I'm not the only one. A useful print to repair an air vent part for Toyota Prado. In the photos, the 1st one is the printed model, in the 2nd one the original part by Toyota.

Toyota HiLux/Prado/Fortuner Sump Drain Tray

This is a model of the genuine Toyota part that helps redirect oil draining from your sump. It slots in between the sump and the bar that runs below it, to stop oil splashing onto the bar. This model is slightly oversized, as the vehicle…

GME XRS Prado adapter plate

The Prado has a lot of contoured surfaces, without having anywhere flat to stick the GME XRS mount this adapter plate fits the bill. Using all the supplied hardware in the GME kit its as simple as taking off the flat plate and replacing…

Rear Door Spare Wheel Cover Screw Mount Hole Plug for Toyota LandCruiser Prado 150

Plug for the spare wheel cover mounting anchors that remain when you remove the plastic trim bits on a Toyota LandCruiser Prado 150. The pin inside the plug is a simple friction fit into the plastic screw anchor. I've printed these in TPU…

Prado Can Holder

Sick of cans or stubbys rolling around in your Prado cool box , print this and off ya go! Printed in PETG .3 or .2 layer height print flat side down I printed with no top or bottom layers to see honey comb effect

Toyota Prado 150 series (2013) Square Cupholder

Insert for the somewhat useless square cup holder in a Toyota Prado 150 series. This version fits a large (36oz / 1065ml) Yeti bottle and a small tray (to hold fries on a road trip :-)) Also a cutout for a coffee cup handle. It covers the…

Toyota Land Cruiser Prado 150 back window handle

Ручка двери заднего стекла Toyota Land Cruiser Prado 150, позволяющая закрыть его изнутри. Прикрепляется родными болтами. Просто снимите оригинальную деталь (она крепится клипсами, расположение клипс можно увидеть по отверстиям на…

Fuel Nozzle Pins Holder for Toyota LandCruiser Prado 150

A convenient holder for the Fuel Nozzle Pins (thanks to rekrapd for the design, original unmodified file attached as fuel_nozzle_pins_v1.stl to this project in case Thingiverse evaporates) that sits in the fuel filler door on the Toyota…

Toyota Prado Rear Door Stopper Guide / Anti-Rattle Bumper Upgrade

Prado cool box 6 pack holder

Prado cool box 6 pack cooler , Using a large Willow ice brick this little bad boy in combination with the aircon cool box of the Prado will keep 6 beers cold all day!

Real size Toyota Land Cruiser Prado GX logo

My friend was looking for a way to get rid of chrome but meantime willing to keep original parts safe. Here we go. GX size: 110:24mm Toyota logo is 100mm on wider side projection.

Prado 150 spare wheel spacer - 6mm

6mm wheel spacer for spare tyre to make fitting wheel bags easier Print in place

Trim clip (Ford Falcon, Prado, maybe others)

Original in yellow, my version in orange, I put some extra material in places where it shouldn't matter, and to make it a little tighter.

Prado 150 Rockarmour rear door boxes

Box to fit the Rockarmour Prado 150 door pockets

Prado (120) Upper Vent Phone Holder Adapter

This adapter allows a phone holder/cradle to be held by the upper left air vent (upper right if the steering wheel is on the wrong side) on 120 Prados, placing the phone in a much higher and more visible position, making it much easier to…

Toyota Prado Rear-Door Water Tank

This is a slim water tank I designed to fit inside the Toyota Prado rear door cavity. It can be used to store non-drinking water and used for handwashing, cleaning, etc. It should fit on any J150 Prado (roughly 2009–2023) if the rear door…

Prado 120 series side vent guide

The side air conditioning vents in my old beast had become brittle with heat and age and deteriorated. I dismantled the vent units and found both the vertical and horizontal guides needed to be rebuilt. Being unable to find an existing…

TOYOTA key fob land cruiser corolla prius camry highlander avensis prado

6cm*2.5cm*0.37cm can be scaled as desired 2 models included: 1 with toyota logo on the back, 2 without logo. during printing you can change the filament to another color and the TOYOTA inscription will be in a different color.

Toyota Landcruiser Prado 250 CB radio mount

CB Radio handset mount for toyota Landcuiser prado 250. Print on it's side, clip the bottom underneath the trim and bend the top back a little to clamp it over the drink holder. Needs 2x M3 nuts for the back - just push them into the…

Toyota LC250 Prado RoofRail Mount Brackets

Printed inserts to be used with 2" Bullbar brackets. Printed with PETG 75% infill. I take no responsibility for loss or damage of property or harm to anyone.

Base para Soprador de Ar Turbo

Ta cansado de deixar seu Soprador jogado em qualquer lugar ou de ver ele caindo o tempo todo por esbarrar nele sem querer? Pois aqui ta a solução! uma estação pra deixar ele de pé com mais charme ;D Recomendação: pode ser impresso com…

Toyota Land Cruiser Prado 2023 Front and Rear Bumper Protection

My personal solution for off-road car

Toyota Prado 2006

TOYOTA PRADO 3D MODEL

Toyota Prado Rear-Door Water Tank

This is a slim water tank I designed to fit inside the Toyota Prado rear door cavity. It can be used to store non-drinking water and used for handwashing, cleaning, etc. It should fit on any J150 Prado (roughly 2009–2023) if the rear door…

Toyota Land Cruiser (Prado) J250 Wall Art

Toyota Land Cruiser (Prado) J250 Wall Art

Trim clip (Ford Falcon, Prado, maybe others)

Original in yellow, my version in orange, I put some extra material in places where it shouldn't matter, and to make it a little tighter.

Toyota Land Cruiser Prado 150 back window handle

Ручка двери заднего стекла Toyota Land Cruiser Prado 150, позволяющая закрыть его изнутри. Прикрепляется родными болтами. Просто снимите оригинальную деталь (она крепится клипсами, расположение клипс можно увидеть по отверстиям на…

Toyota Land Cruiser (Prado) J250 Wall Art

Toyota Land Cruiser (Prado) J250 Wall Art