21 modeli
RFID scanner/writer for PC/Mac - based on Raspberry Pi zero and RC522 RFID. A quality USB RFID code reader/writer costs over $220. This system costs less than $20. You will need: Raspberry Pi Zero (W) RFID-RC522 expansion module Pi Zero…
Wydruk około 1,47 €–1,80 € nettoWstępna wycena dla PETGMateriał u źródła: PET
A box to contain an arduino nano connected with a rc522 rfid module. Not Fully satisfy by Dgoma box design ( http://www.thingiverse.com/thing:1413827 ) I decide to make my own. Like Dgoma I could only recommend the Miguelbalboa's work for…
Make sure you have everything wired correctly before pushing the cover in, disassembling is a bit tricky, used small tolerances.
Hanging brackets made for M3 screws. I recommend having the bridges and supports set up properly beforehand. Added version of bottom piece with screw holes inside.
This is a case to hold the RFID sensor. The leads protrude from the back and can be plugged into a breadboard easily. I made it to hold my DIY Prototyping projects. It also supports Inventr.io kits. It snaps together and can be plugged…
This is case for MFCR522 RFID reader and Arduino Nano. It's part of a bigger project you can find on GitHub . The other parts are Arduino firmware and C#/.NET library for communicating with the reader trough serial port. Print…
Enclosure for the popular rc522 module. A ring indicates the location of the antenna. To be mounted with double sided adhesive tape (like for bathroom mirrors). There are extra areas to apply the tape on the back side. Thereby it can be…
Hello, a quick remix for my Decathlon RC500 (flat stem). Print in PETG, 0.2 is fine, but you can try 0.16.
Here is a design to hold two Boss RC505 Loopers at an easy to use position. The photos shows RC505mkii (top) and RC505mki (bottom) loopers. The looper trays are pretty big and I printed them on Rat Rig V-Core 3 400mm printer. I had to…
Mountable cover for a RFID RC522 module. Screw holes are 3mm in diameter. I mounted this in lauan plywood for an escape room puzzle. I wanted to make sure the module was as close as possible to pick up the RFID tag. Most models I saw were…
I 3D scanned my ARC5 and sculpted a wallmount holder around it. Print with support, see photo. I didn't spend the time designing something easy to print. There's a hole in the back, this fits a 12mm magnet, which can be held in place with…
A little mounting plate for your RC5 Loop Station which allows adding some velcro without messing with the perinstalled rubber pad. Installation Remove screws Add plate Install screws Done
Remix for ESP8266 D1 mini and RC522 mini that I had laying around. You only need to change the bottom part. Print the others parts from the original project .
i printed out this raspberry pi case here. https://www.printables.com/model/605060-raspberry-pi-5-case-wpower-button-v2 but with my initial raspberry pi project id like a screen and rfid reader. I found a case for the oled screen no…
Thanks to user Alvomane for creating the 3D scanned model of the shaver. https://www.printables.com/model/1467674-panasonic-es-lv67-3d-laser-scans-sermoon-s1-and-ei A simple and ergonomic wall-mount holder that can be used with or without…
This is designed to snuggly brace the reader for LEGO applications. The disk is a spacer to for soldered leads.
Panasonic ARC5 ES-LV65 wall mounted holder
This is too mount your Quanum Diversity to any gopro mounts! Quanum RC540R 5.8GHz 40CH Race Band FPV Diversity Receiver Print Settings Printer Brand: Ultimaker Printer: Ultimaker 2 Rafts: No Supports: Yes Resolution: 0.2mm Infill: 20-25%…
Quanum RC216R / RC540R tripod mount not sure if it fits others then my tripod, but i though i upload it anyway Print Settings Printer Brand: Wanhao Printer: Wanhao Duplicator i3 V2 Rafts: No Supports: No Resolution: 0.2 Infill: 15%…
Das sind die Gehäuse Teile für einen Raspberry PI 4 und einer RFID-RC522 Platine , sowie einer Ablage für einen Barcode Scanner , dem PI Gehäuse und eines Ablage Fach . Das eigentlich Projekt ist ein Werkzeug Ausgabe-Rückgabe System , Das…
Das sind die Gehäuse Teile für einen Raspberry PI 4 und einer RFID-RC522 Platine , sowie einer Ablage für einen Barcode Scanner , dem PI Gehäuse und eines Ablage Fach . Das eigentlich Projekt ist ein Werkzeug Ausgabe-Rückgabe System , Das…
