Safe-O-tronic LSW101 Battery Lids
2 lids. Best to print them “standing up” to maximize strength in the tabs.
Wydruk około 1,41 €–1,72 € nettoWstępna wycena jednego wariantu
- Pobrania
- 9
- Polubienia
- 0
- Ocena
- 0
Liczymy pasujące modele…
2 lids. Best to print them “standing up” to maximize strength in the tabs.
Wydruk około 1,41 €–1,72 € nettoWstępna wycena jednego wariantu
The EMD SW 1500 is a American diesel switcher locomotive made by General Motors' Electro-Motive Division during the 60's and 70's. Some 800 were made and there are several still in serivce in the United States. This 1:32 scale version of…
Gehäuse für HomeMatic HM-LC-Sw1-PCB Funk-Schaltaktor 1fach. Zum Fixieren wird eine M3x5 Schraube benötigt. Ich habs mit PETG gedruckt…
Protect your e-bike computer from crash damage and trail scratches with this low-profile protective bumper case. This model is a friction-fit "sock" that slides directly over the display body to absorb impacts without blocking the screen…
I made a canopy flasher for the ASW15/20. Not fully finished. It is big because the lights from Aliexpre are very long. Lights I used:…
Sony ICF-SW10 Battery bay cap. Need supports for the 3 pins
Gehäuse für Homematic Schaltaktor für Batteriebetrieb HM-LC-Sw1-Ba-PCB.
I have a Ride1Up Roadster V2 ebike that uses this display that is somewhat common on other ebikes. But the problem with it is the plastic is brittle and the clamp is just a bit smaller than my handlebar so you can't really tighten in all…
Gridfinity holder for a Surecom SW102 SWR Meter. Holds 3 RF (Type N or PL) adapters in a 2 x 3 grid.
I printed it with support. If the cap does not fit perfectly because the screws have tolerances, just scale it. There is 5mm space for 20mm diameter washers. I needed this for two washers.
Bracket to put SW102 display lower on handlebars, to avoid damages.
Karosserie-Pad 30x40 SW13-T5 02 Ausbeul Pad wird nach einfügen einer M8 Mutter oder Schraube an entsprechende Stelle in leichte Beule des Fahrzeugs geklebt. Durch ziehen am befestigten Pad wird versucht die Beule zurück zu ziehen. Danach…
So the hinge on my Eggrider broke and I needed a way to fix it. The protector I remixed worked as a good reference for making this holder, even though my Eggrider model does not fit the original part, due to being the older(?) offset…
Simple, easy to print part I made for my lathe. Scale for other sizes.
These supports, right and left, are for tiny servos Protronik 7350 MG-D in a rc plane, ASW15 from Silencemodel, http://silencemodel.fr/product.php?id_product=1274 . Total weight is 2,4g Print Settings Printer: Mini Fabrikator 2 Rafts: No…
This is a mount I designed to place the Eggrider V2 display directly above the left (or right) handle of my Catrike Dumont. It goes into the end of a 7/8" tube and should work for other trikes that use 7/8' handles. I wanted my display to…
Tool to replace aerator (perlator). It fits aerator with M18 thread which has a spanner seat for 16mm It has a tight fit. That is necessary to have good grip to put the aerator out and in. You might press it in careful with some force.
An adapter for M6 hexagon nuts with 9mm for a wrench with 13mm or a ratchet with 1/4". The Innerdiameter is 6.4mm so if you can't cut the rod it is still possible to tighten the nut. Dimensions: Ø15x50mm With 100% infill ca 7g Worked with…
Mouse Droid (MSE-6-series Repair Droid) - Black - Dark Bluish Gray, Open Stud Wheels sw1004 Droid Should be scale up to 400% in order to have good results. Building instructions This droid is present in the building instructions for LEGO…
Astromech Droid, R2-D2 - sw1385 Droid Should be scale up to 400% in order to have good results. Building instructions This droid is present in the building instructions for LEGO set 75397. LEGO set 75397 building instructions Parts Part…
Climate sensor bracket that takes minutes to print. Made it so you dont need to use doublesided tape on the sensor itself. Clip in place. Used filament: PLA Supports: Organic Printer: Ender 3 Max Neo
sw1120 - Snowman Gonk Droid (GNK Power Droid) Printable parts for Snowman Gonk Droid (GNK Power Droid) . Compatible with lego building blocks. Scale every STL to 200-400%. BUILDING REFERENCE The model corresponding to this reference is…