Liczymy pasujące modele…
I made this model to mount the powersupply for my lenovo dockingstation under my desk. quite a simple design, but i coulndt find it anywhere else, so i made my own :)
Milwaukee M12 Battery Power Supply ZK-4KX 35W MODULE CASE TOOLS / HARDWARE NEEDED ------------------------------------------ 1X ZK-4KX BUCK BOOST CONVERTER (35W) 2X 14/16AWG FLAG TERMINALS 2X 24mm - 1/4" Male Spade Crimp Terminals 6.3mm…
This is my custom design case for powerbank It use 6 cells 3s2p configuration that suitable with this powerbank control board. Print setting: Filament is PLA-F, this type of filament has some flexible compare to PLA No support needed 0.2…
This is case for USB Load tester KZ35. I added also banana holes for probes. Print without suppot and raft, 1,2mm layer and 30% infill. Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: No Resolution: 1,2 Infill:…
Remix and adaption of Whitys model of a case for the MacBook charger, that prevents the charger from scratches. This one fits snug on the 35W power adapter. Please leave a like and/or a review if you like it.
Its an extend to the original LG 35wn75c monitor stand, it rises the monitor 6.5 cm (2.55 inches) with hexagon mesh to make it both light and strong, it fits under the original mount, i designed it with a minimal mistake in width but does…
FOOT 5CM ATEZR V35 PLUS 35W LASER ENGRAVER
A two-piece base for Lenovo's 135W chargers. This model stabilizes your charger, preventing it from falling over. You'll need six M3 x 14mm countersunk bolts, together with six M3 hexagon nuts. The model can be printed without support…
This is a simple bracket for mounting the 135W Slim Lenovo Thinkpad charger, the hole spacing is compatible with Multiboard layout. Used some 9mm T-bolts to fix it to the pegboard holes. I printed it with 0.3mm layers and 0.4mm nozzle, 2…
Toyota Prius Gen5 have a lot of usb ports, but the usb module it uses only supply 5v@3a max, which is not a common setup that most mobile phone accepts. This means a lot of phone and tablet will have very bad charging rate when using…
Created with Tinkercad Revolve tool for the curve and Sketch tool for the profile, a simple mount that holds the phone against the back of the monitor and it is just right to do meetings with. A simple 30 minute design, 90 minute print.…
Replacement Wedges 035WDG for Manfrotto Super Clamp 035. They are to replace always lost/misplaced wedges that are supposed to be stored near securing screw. Print in PETG/ABS/ASA.
!Euro plug extension & ASA material required! This holder allows you to take the charger hide it or take it with you!
!Euro plug extension & ASA material required! This holder allows you to take the charger hide it or take it with you!
Created with Tinkercad Revolve tool for the curve and Sketch tool for the profile, a simple mount that holds the phone against the back of the monitor and it is just right to do meetings with. A simple 30 minute design, 90 minute print.…
Its an extend to the original LG 35wn75c monitor stand, it rises the monitor 6.5 cm (2.55 inches) with hexagon mesh to make it both light and strong, it fits under the original mount, i designed it with a minimal mistake in width but does…
I use this mount under my desk to keep the power supply stored under the table.
A simple bracket for the Lenovo 135W charger. Can be screwed under a table, the charger simply slides in.
My first drawing ever, first experience with Fusion 360. Enjoy
Remix that allows the usage of 35Watt Hama charger
