Liczymy pasujące modele…
(English below) Irgendwann kommt jeder Fahrer eines Audi 80 B3/B4, Audi Cabriolets, Audi Coupe (Typ89), Audi 100/A6 C4, Audi A4 B5 (und etlichen weiteren Modellreihen von VAG aus den 80er bis 2000er Jahren) an den Punkt, dass das Auto…
Frame for an aftermarket radio fitted to a polo 9N Should also fit a Golf IV Radio dimensions: 177x101mm
1-DIN Radioblende VW Viele Fahrzeuge haben werksmäßig einen Doppel-DIN Radioschacht, bei dem nach der Umrüstung auf ein herkömmliches 1-DIN-Radio ein Schacht frei bleibt. Dieses Ablagefach ermöglicht es Ihnen das originale VW Doppel-DIN…
Its not perfect, but it werks!
My polo had this knob missing from the dome light in the back seat, soooo after looking for a replacement(which are either hard to find or expensive), i came up with this simple design for a knob, there is also a ".step" file if you…
A quick and dirty adaption of the Matek M9N-5883 holder for the 5" ImpulseRC Apex frame. Mounts the GPS out the back and at a slight angle. Use self-tapping screws or machine screws + superglue as a ‘threadlocker’. Can also put down a…
Gridifinity Holder for Klein Tools J2000-9NE Side Cutter Linemans Pliers
Small keychain pendant of the Crosspolo 9N3
Uses F695-2RS Bearings Now added a MGN9 Version with all M3 bolts thanks to SlickChris from Discord! Also added a roller version with all M3 bolts.
Snapmaker J1 Bavaria Filament PETG-CF black Temperature : 255C Heat bed : 80C Infill 50% Speed 70 mm/s
Snapmaker J1 Bavaria Filament PETG-CF black Temperature : 255C Heat bed : 80C Infill 50% Speed 70 mm/s
To fit the mount you will require: *M3 50mm bolts x 4 preferably countersunk (45mm should work, the 40mm I had on hand were too short) *M3 nylock nuts x 4 *M3 washers x 4 (optional - should help prevent the nuts damaging bolt holes in…
I created this model, to fit the linked MagSafe Charger. You have to unscrew the ball from the original one and attach it to the printed part, with the original screw. You have to use an, i guess it was M2, Brass insert. The used Charger:…
I had a K9ND Speedster2 lying around, without the I/O shield. So I made one using TinkerCad.
A shorter mount than the original designs I remixed from for the Matek M9N-5883 GPS module that I am using for my iFlight Nazgul5 V2 but should fit other XL5 models. Category: R/C Vehicles
Replacement part for adding GPS to the Nazgul5 adapted for the Matek GPS M9N-5883 Category: R/C Vehicles
This is an adapter for the Jebao PP-399N parts washer pump. This is sold as the Buffalo Tools PWP20 20Gal Parts Washer Pump and was the pump used in two different 3.5 Gallon parts washers that I have. If you buy the replacement pump it…
Apologies for the pictures, we sold the car before I had the chance to take proper photos. We bought a Carpodgo T3 Pro (2024 model) for our old 9N3 Polo GTI to replace a troublesome Carpuride unit, has been a much better experience. So I…
Háček #1719N na magnetické nástěnky Fleysen #1711 je jedním z dvojice háčků, kterým si můžete obohatit kovovou nástěnku, kterou vyrábíme v Plesné na západě Čech. Standardně je dodáváme včetně zatištěných magnetů, nicméně fungují i bez…
fits the Gearwrench model 84919N socket set. May fit other similar sets but was specifically modeled for this set.
Custom designed cup holder insert for Volkswagen Polo 9N / 9N3 (2002–2009). Modeled in Autodesk Inventor, optimized for 3D printing. Fits in the center console. Printable with PLA/ABS (recommended 0.2 mm layer height).
IBM NetVista 09N5757 PCI Retention Bracket (Desktop) This is a recreated PCI retention bracket for IBM NetVista desktop systems (FRU 09N5757) . The bracket secures installed PCI expansion cards to the chassis, keeping them aligned with…
This recreated air baffle duct for IBM NetVista systems (FRU 09N5735) helps guide airflow through the chassis to improve cooling efficiency. The duct directs air across key components such as the CPU and motherboard, ensuring proper…
IBM NetVista 09N5773 Fan & Speaker Bracket (with Speaker Mount) This recreated fan and speaker bracket for IBM NetVista systems (FRU 09N5773) mounts the system fan and internal speaker in the correct position within the chassis. The…
Printed on one side, standing, with supports. Pretty finnichy to find a good orientation where the supports go straight to the part they should support, but the knob works, i still use it after more than a year. I printed it with pla
A phone holder for a pixel 3a for a polo 9n that replaces the commonly installed ipod adapter and uses the same mounting point. The mounting point is offset to the left a significant amount to resolve the main issue with the ipod mount's…
Added love VW Logo <3 ~~~~~~~~~~~~~~~~~~~~~~~~~~~~ Printer: Ender 3 v3 SE Nozzle temp: 200 Bed temp: 60 No supports ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
I angled the holder to make it easier to see the screen. I recommend to use some double sided tape to hold it in place a bit better.
Hello Tribe, After Printing the Mk1 version, and it taking forever we changed to the design and added a turrent. hope you enjoy. Edit: Unhappy with the fitment of the powertrain and the axle diameter was shrank. Here is our Sunlu…
Hello Tribe, We present the Combat Vehicle, The axels do rotate. Here is our Sunlu Affiliate link https://www.sunlu.com/?sca\_ref=507104.Qc1O4Eu3lJ Visit us on Patreon.com/thefreeheathenworkshop check out our book…
Hello Tribe, If you don't know who Tech N9ne is you must have not an interest in hiphop. We enjoy Tech N9ne he seems to be a gentleman, and an artist. He is also Odd which happens to be the best part. Here is our Sunlu Affiliate link…
