Liczymy pasujące modele…
This six slot, vertical, AR-10/LR308 magazine holder can be mounted with either female threaded magnets, or screwed to the wall (pre-centered holes provided). If using magnets, I would recommend a minimum of two 35lb+ Neodymium magnets. I…
Simple magazine storage racks for Magpul LR308/SR25 Magazines.
Basic wrench/tool for loosing and tightening AR10 / AR15 butt stock nuts. Best printed at 50% infill or better for best use.
This is a vise block or bench block to mount in an AR10 mag well. Used during assembly and maintenance. Best printed at 50% or better infill if you plan on really clamping in the vise or to the table.
Magazine stands for a wide range of mags. The double stack stand fits most double stack pistol mags - shown below with glock 9mm, S&W .40, S&W 9mm, Taurus 9mm, FN 45ACP, and Taurus 22LR. The single stack version should fit any 9mm-or-less…
A simple remix of a loader I found to make it load from the back instead of from the top. I like plunger-style loaders like this, but I find that the rounds end up getting all wonky when you drop them in from the top. I prefer to load…
For a slat-wall with a distance of 75mm spacing with M5x15mm I am using the aluminum inserts in the wall so you may need different t-nuts if you are not Category: Sport & Outdoors
Hardware Needed: (1) 1/4x28 Bolt - 1.5" or longer (1) 1/4x28 Nut
Holds 3 AR10 mags on the multiboard Printed in Pla+ with 20% infill I think it would be easier to attach to a flush mounted multiboard because it can be difficult to snap in wil the board off the wall but it works and holds full mags just…
print size should be 170.25x85mm to fit the magazines snug
Replacement AR10 PMAG spring baseplate, its pretty sloppy and doesn't have any of the anti-tip bits on it but it fits and works
A replacement spring base designed to allow you to easily and temporarily reduce a 10 round .308/7.62x51 Magpul PMAG to 3 rounds to meet certain states hunting requirements.
Ratchet coupling of arzum hestia blender. I recommend to print it with %100 infill. No support needed. Print Settings Printer Brand: Creality Printer: K1 **Rafts:** Doesn't Matter Supports: No **Resolution:** 0,2mm Infill: 100…
Simple holder for the GraphGear1000 Pen. Can be mounted to a flat surface using double sided tape. The tip of the pen has to be retracted to fit into the holder. Prints without supports/brim.
Support de tournevis VARO – Support vertical avec rangement embouts Support spécialement conçu pour le tournevis électrique VARO VAR10080/25 . Idéal pour organiser ton poste de travail et garder tous tes embouts à portée de main. ✅…
ALL FUTURE MODELS WILL BE SHARED HERE: https://cults3d.com/en/users/antirice/3d-models Not a lot of options out there for AR10 mag holders, and Lancers don't seem to be compatible with the holders made for Magpul mags, so I made my own!…
A stripper clip magazine loader for your 7.62 NATO Caliber M14, M1A, AR10, SR25, LR-308, M77 type rifles.
A raft or brim might be necessary
This compact mount gives your VARO Var10080/25 cordless precision screwdriver a dedicated spot on the IKEA Skådis pegboard. Slide the screwdriver in from the top and it stands upright in the holder, with the inserted bit sticking out…
This is a battery tray for the AR10s. It should also fit the FTX rally car as well. There are a few makers who use the same platform.
Hardware Needed: (1) 1/4x28 Bolt - 1.5" or longer (1) 1/4x28 Nut
Support de tournevis VARO – Support vertical avec rangement embouts Support spécialement conçu pour le tournevis électrique VARO VAR10080/25 . Idéal pour organiser ton poste de travail et garder tous tes embouts à portée de main. ✅…
